Search results for "home security gift"

About Signal BoosterCell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save a life. Unfortunately, there are still some places where one can find themselves - out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: parking lots, tunnels, big stores, office buildings, cars, boats, house in remote areas, etc. Here we will bring you a new kind of LED DCS signal booster. Welcome to buy!Features1. High-gain linear power amplifier. 2. ALC and AGC function technology. 3. Ultra-low noise receive amplifier. 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters. 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications. 7. With full-duplex communication mode. 8. It explores an effective and reasonable method to dispel the heat.Installation Steps1. Use your mobile phone to test signal strength outside house or on roof, -70dBm is the basic requirement (full bar). 2. Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Mount your indoor antenna with signal repeater. 5. Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Notices1. Connect outdoor (BTS) port with outdoor antenna. Connect indoor ANT (MS) port with indoor antenna. Outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away at least from each other. 2. Indoor and outdoor antennas must be separated by wall. 3. If the signal is still weak after installation, please check whether or not the outdoor antenna is pointed to signal tower correctly or elsewhere with stronger signal and confirm that the signal strength achieved -70dBm. 4. If no signal for a long time after installation, please check the device power adapter whether or not connected perfectly and connectors connect well. 5. If strength is not steady, please check if outdoor and indoor antennas are too close. Please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 6. Packed the outdoor connector by waterproof glue, otherwise wet condition will reduce the signal cover area.Specification: General Frequency Range DCS 1800MHz, Uplink 1710-1785MHz, Downlink 1805-1880MHz Gain Uplink 63-67dB, Downlink 63-67dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC:100~240V, 50/60Hz; DC:12V 2A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 198 x 182 x 20mm Weight 1200g Package Include Package Contents 1 x 5dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 1.58kgs / 3.48lb One Package Size 31cm * 23cm * 11cm / 12.2inch * 9.06inch * 4.33inch Qty per Carton 4 Carton Weight 7.40kgs / 16.31lb Carton Size 48cm * 33cm * 24cm / 18.9inch * 12.99inch * 9.45inch Loading Container 20GP: 701 cartons * 4 pcs = 2804 pcs40HQ: 1628 cartons * 4 pcs = 6512 pcs

Read more less

Features1. High-gain linear power amplifier 2. ALC and AGC function technology 3. Ultra-low noise receive amplifier 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters 5. Stable and reliable electromagnetic compatibility design 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications 7. With full-duplex communication mode 8. Dispel the heat effective reasonable, the structure is pretty, the volume is suitableInstall Repeater1. Step 1: Use your mobile phone to test signal strength outside house or on roof, -70dbm is the basic requirement (full bar) 2. Step 2 Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal 3. Step3: Run outdoor coaxial cable into building in a convenient location to connect with signal repeater 4. Step 4: Mount your indoor antenna with signal repeater 5. Step 5: Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal 6. Note: Connect outdoor (BTS) port with outdoor antenna, connect indoor ANT(MS) port with indoor antenna, outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away from each other at least 7. Indoor and outdoor antenna must be separated by wallWorking1. The outside antenna catches the low signal from the mobile base station and delivers it to the cell phone amplifier through the connection cable (coax) 2. After the signal is accepted by the phone amplifier, the device amplifies it 3. Then this amplified signal goes through the connection cable (coax) to the inside antenna 4. And after that, the amplified signal transmits to the cell phoneTechnique Supporting1. If still weak signal receipt after installation, please check if outdoor antenna point to signal tower correctly or elsewhere has stronger signal and confirm signal strength achieve-70DBM. 2. If still have no signal after installation, please check our device power adapter whether connected perfectly? And connectors connect well. 3. If strength is not steady, please check if outdoor and indoor antenna is too close; please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 4. Packed the outdoor connector by waterproof glue, otherwise wet reduce the signal cover areaSpecification: General Frequency Range CDMA 850MHz, Uplink 824-849MHz, Downlink 869-894MHz Gain Uplink 58-62dB, Downlink 58-62dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC: 100~240V, 50/ 60Hz; DC: 5V 1A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 140mm x 98mm x 20mm Weight 280g Package Include Package Contents 1 x 12dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual 1 x Signal Booster Package Weight One Package Weight 0.76kgs / 1.67lb One Package Size 30cm * 12cm * 10cm / 11.81inch * 4.72inch * 3.94inch Qty per Carton 10 Carton Weight 9.80kgs / 21.61lb Carton Size 52cm * 50cm * 32cm / 20.47inch * 19.69inch * 12.6inch Loading Container 20GP: 320 cartons * 10 pcs = 3200 pcs40HQ: 744 cartons * 10 pcs = 7440 pcs

Read more less

1. Power + video 2 in 1 passive twisted transceiver. 2. Tuning fork waterproof DC head, built-in high tension spring BNC. 3. RJ45 connector, HD568B connection method. 4. HD 200 meters, simulation 300 meters. 5. 200 meters power supply, input and output 12V ~ 48V (unregulated chip please select the appropriate power according to the camera voltage). 6. Support HD-CVI/AHD/CVI analog HD cameras and analog ordinary HD cameras. 7. ABS plastic shell, durable to use, small size, delicate design. 8. Power indicator, real-time display of power supply status.Specification: Package Weight One Package Weight 0.07kgs / 0.16lb One Package Size 15cm * 10cm * 2cm / 5.91inch * 3.94inch * 0.79inch Qty per Carton 200 Carton Weight 14.40kgs / 31.75lb Carton Size 48cm * 34cm * 32cm / 18.9inch * 13.39inch * 12.6inch Loading Container 20GP: 510 cartons * 200 pcs = 102000 pcs40HQ: 1185 cartons * 200 pcs = 237000 pcs

Read more less

Features1. High-gain linear power amplifier 2. ALC and AGC function technology 3. Ultra-low noise receive amplifier 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters 5. Stable and reliable electromagnetic compatibility design 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications 7. With full-duplex communication mode 8. Dispel the heat effective reasonable, the structure is pretty, the volume is suitableInstall Repeater1. Step 1: Use your mobile phone to test signal strength outside house or on roof, -70dbm is the basic requirement (full bar) 2. Step 2 Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal 3. Step3: Run outdoor coaxial cable into building in a convenient location to connect with signal repeater 4. Step 4: Mount your indoor antenna with signal repeater 5. Step 5: Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal 6. Note: Connect outdoor (BTS) port with outdoor antenna, connect indoor ANT(MS) port with indoor antenna, outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away from each other at least 7. Indoor and outdoor antenna must be separated by wallWorking1. The outside antenna catches the low signal from the mobile base station and delivers it to the cell phone amplifier through the connection cable (coax) 2. After the signal is accepted by the phone amplifier, the device amplifies it 3. Then this amplified signal goes through the connection cable (coax) to the inside antenna 4. And after that, the amplified signal transmits to the cell phoneTechnique Supporting1. If still weak signal receipt after installation, please check if outdoor antenna point to signal tower correctly or elsewhere has stronger signal and confirm signal strength achieve-70DBM. 2. If still have no signal after installation, please check our device power adapter whether connected perfectly? And connectors connect well. 3. If strength is not steady, please check if outdoor and indoor antenna is too close; please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 4. Packed the outdoor connector by waterproof glue, otherwise wet reduce the signal cover areaSpecification: General Frequency Range WCDMA 2100MHz, Uplink 1920-1980MHz, Downlink 2110-2170MHz Gain Uplink 53-57dB, Downlink 58-62dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC: 100~240V, 50/ 60Hz; DC: 5V 1A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 140mm x 98mm x 20mm Weight 280g Package Include Package Contents 1 x 12dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 1.24kgs / 2.73lb One Package Size 50cm * 17cm * 14cm / 19.69inch * 6.69inch * 5.51inch Qty per Carton 6 Carton Weight 6.79kgs / 14.96lb Carton Size 52cm * 36cm * 44cm / 20.47inch * 14.17inch * 17.32inch Loading Container 20GP: 323 cartons * 6 pcs = 1938 pcs40HQ: 751 cartons * 6 pcs = 4506 pcs

Read more less

About The Product1. PSE series PoE switches not only in price can be mount and desk-top installation comparable to ordinary switch, and, compared to those only work in 0 degree C ~50 degree C environment, plastic shell household switches, they specifially for the network system needs uninterrupted work, such as the IPC security system. 2. All models feature stable performance,come with dual surge protection circuits, so that the MTBF of these switches reaches 150K hours. Usually, these functions are ordinary business switches on the market do not have . 3. The aluminum housing of PSE series switches designed to be very compact, so you can easily put them in a small power supply box. Therefore, they are ideally suited for small projects or home security systems.Features1. Metal aluminium housing supports wall mount and desk-top installation. 2. Unique thermal design, wide operating temperature range -30 degree C ~ 70 degree C. 3. MTBF up to 150K hours, designed for 24-hours-working surveillance system. 4. Maxium PoE output up to 20W/port. 5. Plug and play installation, non-professional can quickly install it.Standards Conformance- IEEE 802.3af & IEEE 802.3at Power over Ethernet - IEEE 802.3 10Base-T - IEEE 802.3u 100Base-TX - IEEE 802.3x Flow Control and Back pressure - IEEE 802.1d Spanning Tree Protocol - IEEE 802.1Q VLAN Tagging - IEEE 802.1x Port Authentication Network Control - FCC Part 15 Class A, CEPower Support1. Power over Ethernet: - PoE Standard: IEEE 802.3af & IEEE 802.3at. - PoE Power Supply Type: End-span & Mid-span. - PoE Output Power: Port 1~8: 48VDC, max. 20W/port. - Power Pins Assignment: 1/2, ,3/6,or 4/5(+),7/8(-). - PoE Ouput Power Budget: 120W in total, depending on connected power supply. - PoE Ports Assignment: Port 1~8: IEEE 802.3af (15.4W/port) or IEEE 802.3at (20W/port) PoE output. - PoE/Data Extends Range: Port 10: up-link,150-meter data transmission 150 meters/490ft. 2. Electrical: - Input Voltage: DC 48V. - AC-DC Power Adapter: Optional 120W, UL-listed,90~264VAC to 48VDC, 50/60Hz, Auto-sensing. - Power Consumption (System on): 2W. - Power Consumption (Full load): 120W. - MTBF: More than 150K hours. - Surge Protection : PPTC active surge current limiting, Transient Voltage Suppressor (TVS).Specification: General Model POE 8+2 Material Metal Input Voltage DC 48V Interface 10/100M Fast Ethernet Operation Range 150m Size 192 x 78 x 29 mm Weight 480g Environment Operating Temperature -30 - 70 Degrees Celsius Storage Temperature -40 - 85 Degrees Celsius Operating Humidity 95% RH, noncondensing Storage Humidity 95% RH, noncondensing Package Include Package Contents 1 x User Manual 1 x Power Supply 1 x Switch 1 x Power Supply (EU, US, AU, UK Optional) 1 x Mounting Screws Set Package Weight One Package Weight 1.26kgs / 2.78lb One Package Size 25.5cm * 18cm * 8.5cm / 10.04inch * 7.09inch * 3.35inch Qty per Carton 10 Carton Weight 13.50kgs / 29.76lb Carton Size 45cm * 38cm * 27cm / 17.72inch * 14.96inch * 10.63inch Loading Container 20GP: 577 cartons * 10 pcs = 5770 pcs40HQ: 1340 cartons * 10 pcs = 13400 pcs

Read more less

About Signal BoosterCell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save a life. Unfortunately, there are still some places where one can find themselves - out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: parking lots, tunnels, big stores, office buildings, cars, boats, house in remote areas, etc. Here we will bring you a new kind of LED signal booster. Welcome to buy!Features1. High-gain linear power amplifier. 2. ALC and AGC function technology. 3. Ultra-low noise receive amplifier. 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters. 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications. 7. With full-duplex communication mode. 8. It explores an effective and reasonable method to dispel the heat.Installation Steps1. Use your mobile phone to test signal strength outside house or on roof, -70dBm is the basic requirement (full bar). 2. Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Mount your indoor antenna with signal repeater. 5. Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Notices1. Connect outdoor (BTS) port with outdoor antenna. Connect indoor ANT (MS) port with indoor antenna. Outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away at least from each other. 2. Indoor and outdoor antennas must be separated by wall. 3. If the signal is still weak after installation, please check whether or not the outdoor antenna is pointed to signal tower correctly or elsewhere with stronger signal and confirm that the signal strength achieved -70dBm. 4. If no signal for a long time after installation, please check the device power adapter whether or not connected perfectly and connectors connect well. 5. If strength is not steady, please check if outdoor and indoor antennas are too close. Please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 6. Packed the outdoor connector by waterproof glue, otherwise wet condition will reduce the signal cover area.Specification: General Frequency Range GSM 900MHz, Uplink 890-915MHz, Downlink 935-960MHz Gain Uplink 63-67dB, Downlink 63-67dB Output Power Uplink 15-19dBm, Downlink 15-19dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC:100~240V, 50/60Hz; DC:12V 2A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 198 x 186 x 20mm Weight 1200g Package Include Package Contents 1 x 12dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 2.36kgs / 5.21lb One Package Size 52cm * 26cm * 15cm / 20.47inch * 10.24inch * 5.91inch Qty per Carton 2 Carton Weight 5.60kgs / 12.35lb Carton Size 54cm * 28cm * 32cm / 21.26inch * 11.02inch * 12.6inch Loading Container 20GP: 551 cartons * 2 pcs = 1102 pcs40HQ: 1279 cartons * 2 pcs = 2558 pcs

Read more less

Features1. High-gain linear power amplifier 2. ALC and AGC function technology 3. Ultra-low noise receive amplifier 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters 5. Stable and reliable electromagnetic compatibility design 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications 7. With full-duplex communication mode 8. Dispel the heat effective reasonable, the structure is pretty, the volume is suitableInstall Repeater1. Step 1: Use your mobile phone to test signal strength outside house or on roof, -70dbm is the basic requirement (full bar) 2. Step 2 Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal 3. Step3: Run outdoor coaxial cable into building in a convenient location to connect with signal repeater 4. Step 4: Mount your indoor antenna with signal repeater 5. Step 5: Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal 6. Note: Connect outdoor (BTS) port with outdoor antenna, connect indoor ANT(MS) port with indoor antenna, outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away from each other at least 7. Indoor and outdoor antenna must be separated by wallWorking1. The outside antenna catches the low signal from the mobile base station and delivers it to the cell phone amplifier through the connection cable (coax) 2. After the signal is accepted by the phone amplifier, the device amplifies it 3. Then this amplified signal goes through the connection cable (coax) to the inside antenna 4. And after that, the amplified signal transmits to the cell phoneTechnique Supporting1. If still weak signal receipt after installation, please check if outdoor antenna point to signal tower correctly or elsewhere has stronger signal and confirm signal strength achieve-70DBM. 2. If still have no signal after installation, please check our device power adapter whether connected perfectly? And connectors connect well. 3. If strength is not steady, please check if outdoor and indoor antenna is too close; please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 4. Packed the outdoor connector by waterproof glue, otherwise wet reduce the signal cover areaSpecification: General Frequency Range CDMA 850MHz, Uplink 824-849MHz, Downlink 869-894MHz Gain Uplink 58-62dB, Downlink 58-62dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC: 100~240V, 50/ 60Hz; DC: 5V 1A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 140mm x 98mm x 20mm Weight 280g Package Include Package Contents 1 x 12dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 5m RG6-50 OHM Indoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual 1 x Signal Booster Package Weight One Package Weight 1.39kgs / 3.07lb One Package Size 51cm * 25cm * 10cm / 20.08inch * 9.84inch * 3.94inch Qty per Carton 6 Carton Weight 10.00kgs / 22.05lb Carton Size 52cm * 52cm * 32cm / 20.47inch * 20.47inch * 12.6inch Loading Container 20GP: 308 cartons * 6 pcs = 1848 pcs40HQ: 715 cartons * 6 pcs = 4290 pcs

Read more less

About Signal BoosterCell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save a life. Unfortunately, there are still some places where one can find themselves - out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: parking lots, tunnels, big stores, office buildings, cars, boats, house in remote areas, etc. Here we will bring you a new kind of LED signal booster. Welcome to buy!Features1. High-gain linear power amplifier. 2. ALC and AGC function technology. 3. Ultra-low noise receive amplifier. 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters. 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications. 7. With full-duplex communication mode. 8. It explores an effective and reasonable method to dispel the heat.Installation Steps1. Use your mobile phone to test signal strength outside house or on roof, -70dBm is the basic requirement (full bar). 2. Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Mount your indoor antenna with signal repeater. 5. Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Notices1. Connect outdoor (BTS) port with outdoor antenna. Connect indoor ANT (MS) port with indoor antenna. Outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away at least from each other. 2. Indoor and outdoor antennas must be separated by wall. 3. If the signal is still weak after installation, please check whether or not the outdoor antenna is pointed to signal tower correctly or elsewhere with stronger signal and confirm that the signal strength achieved -70dBm. 4. If no signal for a long time after installation, please check the device power adapter whether or not connected perfectly and connectors connect well. 5. If strength is not steady, please check if outdoor and indoor antennas are too close. Please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 6. Packed the outdoor connector by waterproof glue, otherwise wet condition will reduce the signal cover area.Specification: General Frequency Range WCDMA 2100MHz, Uplink 1920-1980MHz, Downlink 2110-2170MHz, GSM 900MHz, Uplink 890-915MHz, Downlink 935-960MHz Gain 65dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Automatic Gain Control >20dB Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <2 MTBF >50000h Power Supply AC:90~265V, 50/60Hz; DC:12V 2A Power Consumption <20W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 198 x 182 x 20mm Weight 1200g Package Include Package Contents 1 x 9dB Outdoor Antenna 1 x 5dB Indoor Antenna 1 x 5m RG6-50 OHM Indoor Coaxial Cable 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 3.78kgs / 8.34lb One Package Size 39cm * 22cm * 20cm / 15.35inch * 8.66inch * 7.87inch Qty per Carton 4 Carton Weight 15.90kgs / 35.05lb Carton Size 51cm * 45cm * 45cm / 20.08inch * 17.72inch * 17.72inch Loading Container 20GP: 258 cartons * 4 pcs = 1032 pcs40HQ: 599 cartons * 4 pcs = 2396 pcs

Read more less

About Signal BoosterCell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save a life. Unfortunately, there are still some places where one can find themselves - out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: parking lots, tunnels, big stores, office buildings, cars, boats, house in remote areas, etc. Here we will bring you a new kind of LED DCS signal booster. Welcome to buy!Features1. High-gain linear power amplifier. 2. ALC and AGC function technology. 3. Ultra-low noise receive amplifier. 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters. 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications. 7. With full-duplex communication mode. 8. It explores an effective and reasonable method to dispel the heat.Installation Steps1. Use your mobile phone to test signal strength outside house or on roof, -70dBm is the basic requirement (full bar). 2. Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Mount your indoor antenna with signal repeater. 5. Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Notices1. Connect outdoor (BTS) port with outdoor antenna. Connect indoor ANT (MS) port with indoor antenna. Outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away at least from each other. 2. Indoor and outdoor antennas must be separated by wall. 3. If the signal is still weak after installation, please check whether or not the outdoor antenna is pointed to signal tower correctly or elsewhere with stronger signal and confirm that the signal strength achieved -70dBm. 4. If no signal for a long time after installation, please check the device power adapter whether or not connected perfectly and connectors connect well. 5. If strength is not steady, please check if outdoor and indoor antennas are too close. Please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 6. Packed the outdoor connector by waterproof glue, otherwise wet condition will reduce the signal cover area.Specification: General Frequency Range DCS 1800MHz, Uplink 1710-1785MHz, Downlink 1805-1880MHz Gain Uplink 63-67dB, Downlink 63-67dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC:100~240V, 50/60Hz; DC:12V 2A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 198 x 182 x 20mm Weight 1200g Package Include Package Contents 1 x 12dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 5m RG6-50 OHM Indoor Coaxial Cable 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 2.78kgs / 6.13lb One Package Size 51cm * 23cm * 15cm / 20.08inch * 9.06inch * 5.91inch Qty per Carton 2 Carton Weight 5.60kgs / 12.35lb Carton Size 53cm * 25cm * 32cm / 20.87inch * 9.84inch * 12.6inch Loading Container 20GP: 628 cartons * 2 pcs = 1256 pcs40HQ: 1460 cartons * 2 pcs = 2920 pcs

Read more less

**Specification 1) Frequency range: -Up link GSM 890-915 -Downlink GSM 825-960 2) Gain(dB) GSM Up link: 55 3) GSM downlink: 60 4) Gain adjustable range: GSM950/ 50Db~55Db 5) Output power(dBm): ≥27 / 30 6) Pass band ripple GSM: 4dB 7) Guard band rejection: GSM(BW-60dB)≤42 MHz (BW-70dB)≤45 MHz 8) I/O impedance: 50Ω 9) I/O return loss: ≤-10dB 10) Noise coefficient: ≤5dB 11) Intermodulation attenuation (Po=13dBm): ≥40dBc 12) Transmission delay: ≤0.5us 13) Ambient temperature: -10℃～60℃ 14) Power supply: AC220V / DC 12V 45～55Hz **Characteristic 1) Fully integrated 980 MHz antenna system 2) Powerful amplifier enables up to + 85 dB of signal gain including cable loss 3) Intelligent signal processing and real time adaptive operation 4) Automatically adjusts power levels as needed to ensure a consistent coverage footprint 5) Reprogrammable (in the field) enabling spectrum or carrier reconfigurations as needed 6) Auto-track LED diagnostics displays aid install and operation 7) Patented algorithms and adaptive processing ensure our products will not interfere with other wireless frequencies or radio devices **The package contains: 1) 55dB GSM cellular phone signal amplifier 2) 9dB outdoor antenna 3) 3dB indoor antenna 4) 10m cable 5) Mounting accessories 6) AC power supplySpecification: Package Weight One Package Weight 1.25kgs / 2.75lb One Package Size 23.5cm * 15cm * 5cm / 9.25inch * 5.91inch * 1.97inch Qty per Carton 10 Carton Weight 17.40kgs / 38.36lb Carton Size 49cm * 32cm * 22cm / 19.29inch * 12.6inch * 8.66inch Loading Container 20GP: 773 cartons * 10 pcs = 7730 pcs40HQ: 1794 cartons * 10 pcs = 17940 pcs

Read more less

1. 100% Brand new and high quality. 2. Compatible with all HD-CVI, HD-TVI, HD-AHD. 3. Transmission Distance: HD-CVI, HD-TVI, AHD camera 720p up to 300m, over UTP cable. 4. Can transport audio signal and power supply signal at the same time. 5. Built-in transient suppression protection. 6. Super interference rejection.Specification: General Model HD 213A Material Metal, ABS Size 14.5*3.5*2.0cm Weight 70g Package Weight One Package Weight 0.16kgs / 0.35lb One Package Size 15cm * 10cm * 3cm / 5.91inch * 3.94inch * 1.18inch Qty per Carton 100 Carton Weight 10.40kgs / 22.93lb Carton Size 52cm * 32cm * 32cm / 20.47inch * 12.6inch * 12.6inch Loading Container 20GP: 500 cartons * 100 pcs = 50000 pcs40HQ: 1162 cartons * 100 pcs = 116200 pcs

Read more less

1. A perfect item for any drivers and home uses 2. Simply hang on the stanchion of the car seat with the fixing strip 3. Store and secure your umbrella within reach 4. Protects the umbrella from damage 5. Keeps the interior apartment dry,folding the bottom to prevent rain water from leaking inside the car Specification: General Material ABS, PE Product Size 19*9.5*6.5cm Product Weight 103g Package Weight One Package Weight 0.19kgs / 0.41lb One Package Size 23.5cm * 10.5cm * 10cm / 9.25inch * 4.13inch * 3.94inch Qty per Carton 40 Carton Weight 8.00kgs / 17.64lb Carton Size 55cm * 42cm * 49cm / 21.65inch * 16.54inch * 19.29inch Loading Container 20GP: 235 cartons * 40 pcs = 9400 pcs40HQ: 546 cartons * 40 pcs = 21840 pcs

Read more less