Soldering Iron Tip

Use and maintenance of iron head: 1. The soldering iron head is the heat conducting part of the welding table. It mainly consists of four metal materials: copper, iron, nickel, chromium and tin. - Copper, as a heat conductor, is the main component of the soldering iron head. About 85% of the soldering iron head materials, copper has good thermal conductivity, which is conducive to the rapid heating of the soldering iron head. Good soldering iron heads are made of copper, but some manufacturers use brass, in order to reduce costs, but also reduce the thermal conductivity of the soldering iron head. Iron, which acts as an anticorrosion, is the key factor affecting the service life of the iron head. Good soldering iron head has fine and dense crystal structure and good corrosion resistance. This soldering iron head has long service life and good tin effect. Manufacturers with poor iron plating technology mainly rely on the thickness of the iron plating layer to control the service life of the iron head. Usually, the iron plating layer is thicker and the iron head is not tin, thin and durable. Nickel - plays an anti rust role in iron plating, and is convenient for subsequent chromium plating. Chromium - non stick tin prevents the use of tin to run on the iron head. The general chrome plated time is more than 5 minutes, and the ordinary decorative chrome plating is about 1 minutes. Tin - in the head, in the use of sticky tin parts. This is the composition of the iron head material, indispensable. 2. Keep welding head clean. -Wipe the solder, tin and oxide on the welding head with a special wet sponge. After each use, it is necessary to clean the oxide on the welding head and add new tin on the tin plating layer of the welding head. 3. Keep the tin on the welding head. - This can reduce the oxidation chance of the welding head and make the welded iron head more durable. After use, the new tin layer should be coated only after the humidity of the solder iron is slightly reduced, and the right-to-use tin plating layer can achieve better anti-oxidation effect. 4. Choose low active flux. - The flux with high activity or strong corrosiveness will accelerate the corrosion of soldering iron head when heated, so low corrosive flux should be selected. 5. Clean up oxides immediately. - When part of tin plating layer contains black oxide or rust, it is possible to make the welding iron head tin free and unable to carry out welding work. If tin oxide is found not to be added to tin, it must be cleaned at once. 6. Choose the right soldering iron head. - It is very important to choose the correct size and shape of the welded iron head. Choosing the appropriate welded iron head can make the work more efficient and increase the durability of the welded iron head. Choosing the wrong welding head will affect the efficiency of welding iron, and the quality of welding will also be reduced. - The size of the welded iron head is directly related to the thermal capacity. The larger the welded iron head is, the larger the thermal capacity is, the smaller the welded iron head is, and the smaller the thermal capacity is. When continuous welding is carried out, the bigger the welding iron head is, the lower the temperature drop is. In addition, because of the high thermal capacity of the large welding iron head, it is not easy to oxidize when the welding iron head can be used at a lower temperature, thus increasing its service life. The short and thick welding iron head has long heat transfer and small welding iron head, and is more durable. Flat, blunt iron heads can transmit more heat than sharp iron heads. Generally speaking, the size of soldering head is not affected by adjacent elements. Selecting the geometry dimensions that can fully contact with the solder joints can improve the welding efficiency.Specification: Package Weight One Package Weight 0.05kgs / 0.12lb One Package Size 5cm * 7cm * 1cm / 1.97inch * 2.76inch * 0.39inch Qty per Carton 240 Carton Weight 12.48kgs / 27.51lb Carton Size 24cm * 20cm * 18cm / 9.45inch * 7.87inch * 7.09inch Loading Container 20GP: 3086 cartons * 240 pcs = 740640 pcs40HQ: 7164 cartons * 240 pcs = 1719360 pcs

Read more less

1. Perfectly suited for precision soldering; ideal for multi-layer boards, densely packed components, and hard-to-reach areas.2. Features a needle-point tip design, allowing easy access to narrow spaces.3. The tip ensures precise soldering capability, reflecting excellent craftsmanship and stable performance.4. Made from high-quality, durable, and wear-resistant materials for smooth, consistent output.5. Precision-engineered for tight connections and accurate control; features a smooth body and comfortable grip.6. High-quality materials enable rapid heating and efficient soldering.7. Lead-free, safe, eco-friendly, and compliant with industry standards.Specification: Package Weight One Package Weight 0.03kgs / 0.07lb One Package Size 12.1cm * 3.1cm * 3.1cm / 4.76inch * 1.22inch * 1.22inch Qty per Carton 250 Carton Weight 8.00kgs / 17.64lb Carton Size 41cm * 34cm * 32cm / 16.14inch * 13.39inch * 12.6inch Loading Container 20GP: 597 cartons * 250 pcs = 149250 pcs40HQ: 1387 cartons * 250 pcs = 346750 pcs

Read more less

1. Material: main body plastic, metal soldering iron tip2. Temperature: flame temperature 1300 degrees Celsius (adjustable), soldering iron temperature 450 degrees Celsius (adjustable)3. Fuel used: pure butane GAS (this gas soldering iron does not have automatic ignition, a lighter is required to ignite)4. Filling capacity: about 8ML5. Weight: about 69 gramsFill gas:1. Fill it with gas and make sure that the switch is turned off, and then refill2. Introduce the gas tank into the air hole and press down to inflate.3. It takes about 10 seconds to complete the gas filling, wait a few minutes, wait for the gas to stabilize, and then use it again4. If there is a hissing sound in the tail after the gas has been poured in, use a pen tip to slightly press into the air port to eliminate itignition:1. Replace the soldering iron tip2. Push the switch to the ON position and hear a hissing sound3. Push the electronic switch to ignite4. Burn for 3 minutes after igniting the fire. When the fire is extinguished, the soldering iron tip will continue to heat up5. Adjust the flame size6. The temperature is as high as 1300 degrees Celsius (the soldering iron temperature is 450 degrees Celsius). Please pay attention to safety when using it. Turn off the switch after use.7. When using a gas soldering iron, please pay special attention to wait until the flame is completely eliminated and the object inside the soldering iron turns red before performing the operation to extend the life of the soldering iron tipPrecautions:1. Replace the connector, please wait for it to cool down before replacing it or replace it in advance2. The soldering iron tip in use is hot and hot, please do not touch it with your hands3. The adjustment knob can control the gas output and temperature, usually placed in the middle position4. After use, wait for it to cool down, and store it again. Dont put it in high temperature or direct sunlight.5. Children are not suitable for use, and need to be placed in a proper place when storing6. Please use high-quality canned gas for filling, keep away from the fire source when filling7. Because there is more or less slag in the gas, it is necessary to clean the nozzle frequently8. When cleaning, press the nozzle on the gas outlet of the gas tank to achieve a cleaning effect9. Avoid heavy fallsSpecification: Package Weight One Package Weight 0.20kgs / 0.45lb One Package Size 15cm * 10cm * 4cm / 5.91inch * 3.94inch * 1.57inch Qty per Carton 146 Carton Weight 30.00kgs / 66.14lb Carton Size 50cm * 50cm * 60cm / 19.69inch * 19.69inch * 23.62inch Loading Container 20GP: 177 cartons * 146 pcs = 25842 pcs40HQ: 412 cartons * 146 pcs = 60152 pcs

Read more less

1. Material: copper, chrome-plated alloy2. Application: welding head3. Features: the outer layer is chrome-plated, the surface is bright, not easy to rust, sturdy and durable, and has a wide range of applicability4. Size: length about 4.1 cm/piece5. Weight: 15 pieces of about 71 grams, 17 pieces of about 81 gramsSpecification: Package Weight One Package Weight 0.09kgs / 0.20lb One Package Size 20cm * 10cm * 1cm / 7.87inch * 3.94inch * 0.39inch Qty per Carton 288 Carton Weight 30.00kgs / 66.14lb Carton Size 50cm * 50cm * 60cm / 19.69inch * 19.69inch * 23.62inch Loading Container 20GP: 177 cartons * 288 pcs = 50976 pcs40HQ: 412 cartons * 288 pcs = 118656 pcs

Read more less

1. Lead-free soldering iron tip 2. Easy to carry and use 3. If you leave it on too long or run it too hot it will burn off the solder and go black again 4. You can choose the proper one for different soldering needs 5. These tips are made from copper and not electroplated, easy to tin and diamagnetic, suitable for lower temperature solderingSpecification: Package Weight One Package Weight 0.04kgs / 0.08lb One Package Size 10cm * 10cm * 1cm / 3.94inch * 3.94inch * 0.39inch Qty per Carton 600 Carton Weight 19.00kgs / 41.89lb Carton Size 52cm * 42cm * 32cm / 20.47inch * 16.54inch * 12.6inch Loading Container 20GP: 381 cartons * 600 pcs = 228600 pcs40HQ: 885 cartons * 600 pcs = 531000 pcs

Read more less

1. Lead-free environmental soldering head, multi-layer electroplating2. No need to remove the handle, plug and play, say goodbye to tedious, improve work efficiency3. Durable and good oxidation resistance4. Professional maintenance tools are designed to help with equipment maintenance5. Material: alloySpecification: Package Weight One Package Weight 0.06kgs / 0.14lb One Package Size 10cm * 5cm * 5cm / 3.94inch * 1.97inch * 1.97inch Qty per Carton 468 Carton Weight 30.00kgs / 66.14lb Carton Size 50cm * 50cm * 60cm / 19.69inch * 19.69inch * 23.62inch Loading Container 20GP: 177 cartons * 468 pcs = 82836 pcs40HQ: 412 cartons * 468 pcs = 192816 pcs

Read more less

1. Lead-free welding tips 2. Safe and long working life of soldering tip 3. 3 different shapes and sizes, this special customized tip set can achieve almost any soldering application you need. 4. Tinned with Lead Free alloy, make better heat transfer performance, good ability to hang tin, lifetime is no less than 50,000 welding spots.Specification: Package Weight One Package Weight 0.06kgs / 0.14lb One Package Size 20cm * 6cm * 2cm / 7.87inch * 2.36inch * 0.79inch Qty per Carton 200 Carton Weight 13.00kgs / 28.66lb Carton Size 42cm * 32cm * 42cm / 16.54inch * 12.6inch * 16.54inch Loading Container 20GP: 472 cartons * 200 pcs = 94400 pcs40HQ: 1096 cartons * 200 pcs = 219200 pcs

Read more less