-
FURTHER INFO
-
CUSTOMER SERVICE
-
SHOPPING GUIDE
-
CUSTOMER SUPPORT
Mira Sales 96 Parkers Walk, Newmarket England CB8 7AP United Kingdom
Available between 9AM to 5PM. Ready to answer your questions. Live Chat Support Available.
Boosters
-
WCDMA 2100MHz Signal Booster / 3G Signal Repeater with Sucker Antenna, 2100MHz Signal Booster
Why to use1. Cell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save life of somebody. 2. Unfortunately, there are still some places where one can find themselves out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: 1) Parking lots, tunnels 2) Big stores, office buildings 3) Cars, boats etc. 4) House in remote areas etcFeatures1. High-gain linear power amplifier 2. ALC and AGC function technology 3. Ultra-low noise receive amplifier 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications 7. With full-duplex communication mode. 8. Dispel the heat effective reasonable, the structure is pretty, the volume is suitableHow to work1. The outside antenna catches the low signal from the mobile base station and delivers it to the cell phone amplifier through the connection cable (coax). 2. After the signal is accepted by the phone amplifier, the device amplifies it. 3. Then this amplified signal goes through the connection cable (coax) to the inside antenna. 4. And after that, the amplified signal transmits to the cell phoneHow to install1. Step 1: Use your mobile phone to test signal strength outside house or on roof, -70dbm is the basic requirement (full bar). 2. Step 2: Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Step 3: Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Step 4: Mount your indoor antenna with signal repeater 5. Step 5: Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signalNotes1. Connect outdoor (BTS) port with outdoor antenna, connect indoor ANT(MS) port with indoor antenna, outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away from each other at least. 2. Indoor and outdoor antenna must be separated by wallTechnique supports1. If still weak signal receipt after installation, please check if outdoor antenna point to signal tower correctly or elsewhere has stronger signal and confirm signal strength achieve-70DBM. 2. If still have no signal after installation, please check our device power adapter whether connected perfectly? And connectors connect well. 3. If strength is not steady, please check if outdoor and indoor antenna is too close; please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 4. Packed the outdoor connector by waterproof glue, otherwise wet reduce the signal cover areaSpecification: General Frequency Range WCDMA 2100MHz, Uplink 1920-1980MHz, Downlink 2110-2170MHz Gain Uplink 53-57dB, Downlink 58-62dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC: 100~240V, 50/ 60Hz; DC: 5V 2A Power Consumption <5W RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 100mm x 45mm x 18mm Weight 350g Package Include Package Contents 1 x 12dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 5m RG6-50 OHM Indoor Coaxial Cable 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 1.00kgs / 2.20lb One Package Size 51cm * 18cm * 13cm / 20.08inch * 7.09inch * 5.12inch Qty per Carton 4 Carton Weight 5.20kgs / 11.46lb Carton Size 53cm * 38cm * 28cm / 20.87inch * 14.96inch * 11.02inch Loading Container 20GP: 472 cartons * 4 pcs = 1888 pcs40HQ: 1097 cartons * 4 pcs = 4388 pcs
£26.99
-
Mobile LED GSM 980MHz Signal Booster / Signal Repeater with Sucker Antenna, LED GSM980
About Signal BoosterCell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save a life. Unfortunately, there are still some places where one can find themselves - out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: parking lots, tunnels, big stores, office buildings, cars, boats, house in remote areas, etc. Here we will bring you a new kind of LED signal booster. Welcome to buy!Features1. High-gain linear power amplifier. 2. ALC and AGC function technology. 3. Ultra-low noise receive amplifier. 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters. 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications. 7. With full-duplex communication mode. 8. It explores an effective and reasonable method to dispel the heat.Installation Steps1. Use your mobile phone to test signal strength outside house or on roof, -70dBm is the basic requirement (full bar). 2. Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Mount your indoor antenna with signal repeater. 5. Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Notices1. Connect outdoor (BTS) port with outdoor antenna. Connect indoor ANT (MS) port with indoor antenna. Outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away at least from each other. 2. Indoor and outdoor antennas must be separated by wall. 3. If the signal is still weak after installation, please check whether or not the outdoor antenna is pointed to signal tower correctly or elsewhere with stronger signal and confirm that the signal strength achieved -70dBm. 4. If no signal for a long time after installation, please check the device power adapter whether or not connected perfectly and connectors connect well. 5. If strength is not steady, please check if outdoor and indoor antennas are too close. Please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 6. Packed the outdoor connector by waterproof glue, otherwise wet condition will reduce the signal cover area.Specification: General Frequency Range GSM 900MHz, Uplink 890-915MHz, Downlink 935-960MHz Gain Uplink 63-67dB, Downlink 63-67dB Output Power Uplink 15-19dBm, Downlink 15-19dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC:100~240V, 50/60Hz; DC:12V 2A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 198 x 186 x 20mm Weight 1200g Package Include Package Contents 1 x 5dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 1.39kgs / 3.07lb One Package Size 31cm * 20cm * 11cm / 12.2inch * 7.87inch * 4.33inch Qty per Carton 4 Carton Weight 7.40kgs / 16.31lb Carton Size 42cm * 33cm * 24cm / 16.54inch * 12.99inch * 9.45inch Loading Container 20GP: 801 cartons * 4 pcs = 3204 pcs40HQ: 1861 cartons * 4 pcs = 7444 pcs
£28.99
-
Mobile LED 3G WCDMA 2100MHz Signal Booster / Signal Repeater with Sucker Antenna, Signal Repeater
About Signal BoosterCell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save a life. Unfortunately, there are still some places where one can find themselves - out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: parking lots, tunnels, big stores, office buildings, cars, boats, house in remote areas, etc. Here we will bring you a new kind of LED 3G signal booster. Welcome to buy!Features1. High-gain linear power amplifier. 2. ALC and AGC function technology. 3. Ultra-low noise receive amplifier. 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters. 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications. 7. With full-duplex communication mode. 8. It explores an effective and reasonable method to dispel the heat.Installation Steps1. Use your mobile phone to test signal strength outside house or on roof, -70dBm is the basic requirement (full bar). 2. Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Mount your indoor antenna with signal repeater. 5. Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Notices1. Connect outdoor (BTS) port with outdoor antenna. Connect indoor ANT (MS) port with indoor antenna. Outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away at least from each other. 2. Indoor and outdoor antennas must be separated by wall. 3. If the signal is still weak after installation, please check whether or not the outdoor antenna is pointed to signal tower correctly or elsewhere with stronger signal and confirm that the signal strength achieved -70dBm. 4. If no signal for a long time after installation, please check the device power adapter whether or not connected perfectly and connectors connect well. 5. If strength is not steady, please check if outdoor and indoor antennas are too close. Please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 6. Packed the outdoor connector by waterproof glue, otherwise wet condition will reduce the signal cover area.Specification: General Frequency Range WCDMA 2100MHz, Uplink 1920-1980MHz, Downlink 2110-2170MHz Gain Uplink 63-67dB, Downlink 63-67dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC:100~240V, 50/60Hz; DC:12V 2A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 198 x 182 x 20mm Weight 1200g Package Include Package Contents 1 x 5dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 1.65kgs / 3.64lb One Package Size 31cm * 23cm * 11cm / 12.2inch * 9.06inch * 4.33inch Qty per Carton 4 Carton Weight 7.40kgs / 16.31lb Carton Size 48cm * 33cm * 24cm / 18.9inch * 12.99inch * 9.45inch Loading Container 20GP: 701 cartons * 4 pcs = 2804 pcs40HQ: 1628 cartons * 4 pcs = 6512 pcs
£42.99
-
GSM900 / WCDMA2100 Mini Mobile Phone LCD Signal Repeater with Logarithm Periodic Antenna, GSM900 / WCDMA2100
About The Product1. This micro-repeater kit includes an outdoor and indoor antenna, suitable for mobile phone signal boosting, presenting good amplification effect with no blind spot, which is widely used at home, office, meeting room and other small places. 2. Note: Please ensure your phone frequency the same with our repeater before purchase, for different phone may use different frequency.Features1. GSM900 / WCDMA2100 MHz repeater for mobile phone signal boosting. 2. ALC function, no interference to work station. 3. Low noise, low heat, low power consumption. 4. Alloy material, durable in performance. 5. Perfect design, easy installation. 6. Antenna Gain: 9dB outdoor antenna, 3dB indoor antenna. 7. Indoor antenna cover area: 100-500m2. 8. Frequency range: Uplink 890-915 / 1920-1990MHz, downlink 930-960 / 2110-2180MHz. 9. Gain: Uplink 60dB, downlink 65dB. 10. Output power: Uplink 23dBm, downlink 23dBm. 11. Outdoor Antenna Length: 10m/32.81ft.Specification: General Material Aluminum Alloy Output Power Uplink 23dBm, Downlink 23dBm VSWR <1.5 Power Supply DC12V/2A (AC110-240V) Impedance 50ohm RF Connector N-K Outdoor Antenna Length 10m Cover Area 100-500m2 Seclusion >70dB Dimensions & Weight Size 198*51*22mm Package Include Package Contents 1 x AC Power Supply 1 x Manual 1 x Repeater 1 x Indoor Antenna 1 x Outdoor Antenna Package Weight One Package Weight 3.20kgs / 7.05lb One Package Size 42cm * 22cm * 20cm / 16.54inch * 8.66inch * 7.87inch Qty per Carton 6 Carton Weight 20.50kgs / 45.19lb Carton Size 45cm * 46cm * 62cm / 17.72inch * 18.11inch * 24.41inch Loading Container 20GP: 207 cartons * 6 pcs = 1242 pcs40HQ: 482 cartons * 6 pcs = 2892 pcs
£49.99
-
DCS-LTE 4G Phone Signal Repeater Booster, US Plug(Silver)
1. Cover the blind areas of indoor signals, so that there are no blind corners of indoor signals, and solve the inconvenience caused by blind areas. 2. Intelligently enhance the indoor signal to solve the problems of poor mobile phone signal, instability, and poor reception ability 3. Significantly improve the call quality and efficiently increase the signal strength 4. Improve 4G cellular data transmission, solve mobile phone network freezes, and improve mobile 4G Internet loading speed 5. Frequency range: 1800MHz 6. Indoor ceiling receiver: Install it in a place where there is no signal indoors, about 5 meters away from the window, and can be hung on the wall or ceiling 7. Packing list: Host x 1 Small Antenna x 1 Suction Antenna x 1 Power Supply x 1 Specification: Package Weight One Package Weight 0.80kgs / 1.76lb One Package Size 33cm * 18cm * 7cm / 12.99inch * 7.09inch * 2.76inch Qty per Carton 15 Carton Weight 9.00kgs / 19.84lb Carton Size 56cm * 34cm * 37cm / 22.05inch * 13.39inch * 14.57inch Loading Container 20GP: 378 cartons * 15 pcs = 5670 pcs40HQ: 878 cartons * 15 pcs = 13170 pcs
£13.99
-
Mobile LED GSM 980MHz Signal Booster / Signal Repeater with Yagi Antenna, LED GSM Antenna
About Signal BoosterCell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save a life. Unfortunately, there are still some places where one can find themselves - out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: parking lots, tunnels, big stores, office buildings, cars, boats, house in remote areas, etc. Here we will bring you a new kind of LED signal booster. Welcome to buy!Features1. High-gain linear power amplifier. 2. ALC and AGC function technology. 3. Ultra-low noise receive amplifier. 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters. 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications. 7. With full-duplex communication mode. 8. It explores an effective and reasonable method to dispel the heat.Installation Steps1. Use your mobile phone to test signal strength outside house or on roof, -70dBm is the basic requirement (full bar). 2. Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Mount your indoor antenna with signal repeater. 5. Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Notices1. Connect outdoor (BTS) port with outdoor antenna. Connect indoor ANT (MS) port with indoor antenna. Outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away at least from each other. 2. Indoor and outdoor antennas must be separated by wall. 3. If the signal is still weak after installation, please check whether or not the outdoor antenna is pointed to signal tower correctly or elsewhere with stronger signal and confirm that the signal strength achieved -70dBm. 4. If no signal for a long time after installation, please check the device power adapter whether or not connected perfectly and connectors connect well. 5. If strength is not steady, please check if outdoor and indoor antennas are too close. Please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 6. Packed the outdoor connector by waterproof glue, otherwise wet condition will reduce the signal cover area.Specification: General Frequency Range GSM 900MHz, Uplink 890-915MHz, Downlink 935-960MHz Gain Uplink 63-67dB, Downlink 63-67dB Output Power Uplink 15-19dBm, Downlink 15-19dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC:100~240V, 50/60Hz; DC:12V 2A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 198 x 186 x 20mm Weight 1200g Package Include Package Contents 1 x 12dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 2.36kgs / 5.21lb One Package Size 52cm * 26cm * 15cm / 20.47inch * 10.24inch * 5.91inch Qty per Carton 2 Carton Weight 5.60kgs / 12.35lb Carton Size 54cm * 28cm * 32cm / 21.26inch * 11.02inch * 12.6inch Loading Container 20GP: 551 cartons * 2 pcs = 1102 pcs40HQ: 1279 cartons * 2 pcs = 2558 pcs
£30.99
-
3G Signal Amplifier with Signal Strengthen Antenna, Cable Length: 10m, Signal Amplifier
**Specification 1) Frequency range: - Up link 3G 1920-1980(MHz) - Downlink 3G 2110-2170(MHz) 2) Gain(dB): 3G 53 / 3G 58 3) Gain adjustable range: MGC≥30dB 4) Output power(dBm): ≥20 5) Pass band ripple 3G: 15dB 6) Guard band rejection 3G: (BW-58dB)≤104MHz (BW-70dB)≤107 MHz 7) I/O impedance:50C/N Connector 8) I/O return loss: ≤-10dB 9) Noise igure: ≤-8dB 10) Intermodulation att enuation (Po=13dBm): ≥40dBc 11) Transmission delay: ≤0.5us 12) Ambient temperature: -10℃～50℃ 13) Power supply: AC 110～220V±10% 45～55Hz **Characteristic Fully integrated WCDMA 3G antenna system 1) Powerful amplifier enables up to + 85 dB of signal gain including cable loss 2) Intelligent signal processing and real time adaptive operation 3) Automatically adjusts power levels as needed to ensure a consistent coverage footprint 4) Reprogrammable (in the field) enabling spectrum or carrier reconfigurations as needed 5) Auto-Trac LED diagnostics displays aid install and operation 6) Patented algorithms and adaptive processing ensure our products will not interfere with other wireless frequencies or radio devices 7) Approved by CE **The package contains: 1) 55Db 3G cellular phone signal amplifier 2) 9dB outdoor antenna 3) 3dB indoor antenna 4) Outdoor coaxial cable 10m 5) Mounting accessories 6) AC power supplySpecification: Package Weight One Package Weight 0.78kgs / 1.73lb One Package Size 28cm * 18cm * 9cm / 11.02inch * 7.09inch * 3.54inch Qty per Carton 20 Carton Weight 16.80kgs / 37.04lb Carton Size 58cm * 38cm * 47cm / 22.83inch * 14.96inch * 18.5inch Loading Container 20GP: 257 cartons * 20 pcs = 5140 pcs40HQ: 597 cartons * 20 pcs = 11940 pcs
£29.99
You have seen 31 out of 31 products