Elektronikmodul
-
ZK-PP1K PWM Signal Generator 1Hz-150KHz PWM Pulse Frequency Duty Cycle Adjustable Square Wave Generator
1. Used to generate square wave rectangular wave signals for controlling DC motors or stepper motor drivers; used for servo motors, stepper motors, electric grippers, instead of PLC pulses, etc.2. The matching driver realizes dimming, speed control, solenoid valve control, etc., but it cannot directly drive loads such as electric lamp motor solenoid valves3. Two modes can be selected:- PWM mode a frequency (continuous) duty cycle. Note that the number of pulses cannot be set in this mode, and pulses are always sent;- PULSE pulse mode one positive pulse width time, negative pulse width time, delay start time, pulse number are adjustable.5. With start and stop button, you can also connect an external switch to control the output signal ON/OFF.6. Wide voltage input 3.3-30V, with anti-reverse connection protection.7. The 5.08mm screw terminal is convenient for wiring, with a shell8. Working voltage: 3.3~30V, with anti-reverse connection protection9. Frequency range: 1Hz~150KHz, accuracy is about 1%10. Duty cycle range: 0-100%, 1% step11. Number of pulses: 1-9999, or infinite12. Delayed output time: 0.000s-9999s, the minimum can be set to 1ms13. Positive and negative pulse width length: 0.000s-9999s, the minimum can be set to 1ms14. Signal carrying capacity: less than 30mA15. Output signal amplitude: the amplitude is equal to the supply voltage16. Product size: 79mm x 43mm x 30mm17. Product weight: 40gSpecification: Package Weight One Package Weight 0.05kgs / 0.12lb One Package Size 10cm * 8cm * 5cm / 3.94inch * 3.15inch * 1.97inch Qty per Carton 200 Carton Weight 11.00kgs / 24.25lb Carton Size 52cm * 33cm * 32cm / 20.47inch * 12.99inch * 12.6inch Loading Container 20GP: 485 cartons * 200 pcs = 97000 pcs40HQ: 1127 cartons * 200 pcs = 225400 pcs
£2.99
-
5 PCS HW-183 2A Boost Board DC Boost Module Car / Charging / USB / High Power Conversion Module, HW-183
1. Ultra-wide input and output voltage, ultra-high conversion efficiency2. Small size and adjustable boost module, which can be easily installed in various small devices3. MicroUSB input can be used, and the common voltages of 9V, 12V, 15V, 18V, 24V can be easily obtained through the mobile phone data line with a USB charger or mobile power supply, which is very convenient to use4. Packing: individually packed in anti-static bag5. Type: voltage regulator IC6. Output current: 2A (recommended to use within 1A)7. Input voltage: 2 v--24 v8. Output voltage: 28 v (recommended to use within 26V)9. Size: 30x17x14mmPrecautions:1. This module is a boost module, the output voltage should be greater than the input voltage2. The peak current output current does not exceed 2ASpecification: Package Weight One Package Weight 0.05kgs / 0.12lb One Package Size 6cm * 4cm * 6cm / 2.36inch * 1.57inch * 2.36inch Qty per Carton 200 Carton Weight 11.00kgs / 24.25lb Carton Size 42cm * 32cm * 25cm / 16.54inch * 12.6inch * 9.84inch Loading Container 20GP: 793 cartons * 200 pcs = 158600 pcs40HQ: 1842 cartons * 200 pcs = 368400 pcs
£4.99 £1.99
-
HW-688 DC 5V6A Buck Module 12V24V To 5V Power Supply USB Charging 5A High Power 30W, 24V / 12V To 5V 6A
1. USB mobile phone smart charging, RZC7512 charging control IC can identify the charging protocol and automatically switch the charging mode2. Support the power supply range of 9-36v, covering common 12v and 24v power supplies. Simply connect the module with a wire, and you can output a constant voltage of 5v as a 5v power supply. When using 220v AC, you can use a 12/24v transformer to convert the output first in the connection module3. Socket modification can install a small transformer inside the socket, and then connect the output wire to the module. If there is enough space inside the socket, you can open the socket to expose the output port of the module to the socket for easy use.4. The plug strip with USB socket also needs to be modified. The module comes with a charging identification chip, which can automatically switch the charging mode, and the charging efficiency is higher and safer.5. Output voltage: 5v6. Working voltage: 4.5-5.5v7. Input voltage: 9-36v8. Application scope: USB charging for electric car/motorcycle modification, car power modification, solar battery, portable USB charging, generator USB output, DIY applicationSpecification: Package Weight One Package Weight 0.05kgs / 0.12lb One Package Size 12cm * 6cm * 4cm / 4.72inch * 2.36inch * 1.57inch Qty per Carton 200 Carton Weight 11.00kgs / 24.25lb Carton Size 42cm * 32cm * 32cm / 16.54inch * 12.6inch * 12.6inch Loading Container 20GP: 620 cartons * 200 pcs = 124000 pcs40HQ: 1439 cartons * 200 pcs = 287800 pcs
£2.99 £0.99
-
PDS100 QC4.0 PD3.0 Type-C DC 12-28V 100W Step Down Mobile Phone Quick Charger Module for Huawei SCP/FCP iOS PD
1. Material: Aluminum alloy shell2. Power supply voltage: DC12-28V3. Power: 100W4. Input: DC+TYPE-C dual port input5. Support fast charge protocol: PD2.0 PD3.0 PPS, For Qualcomm QC4+/QC3.0, For Huawei SCP/FCP, For OPPO VOOC, For OnePlus DASH, For iOS 2.4A, For Samsung AFC, For VIVO 9V 2A dual engine, For MediaTek PE2.06. Features:Exquisite and small, the digital tube displays the current and voltage, can switch the display content intelligently, and has strong compatibility. After the fast charge protocol is activated, the digital tube will display the output fast charge protocol type.7. Weight: About 60 grams8. Size: About 5.3x4.6x2.1 cmInstructions for use:1. Withstand voltage within 32V, it is recommended to use within 28V. This module is a pure step-down module and has no boost function. If you want to use 20V output, you must use a DC power supply above 21V; low voltage can reach 6V, but 6V is mostly fast the charge will not be activated, and the output power of 100W can only be reached when the PD is output (PD20V, 5A)2. For low-voltage and high-current fast charging, please use the original data cable. If you want to measure the charging voltage and current, you must use a low-resistance USB meter, otherwise the charging current will be affected.3. OPPO and OnePlus mobile phones must use USB port for charging, QC4+/QC4.0/PD3.0 and other protocols must use TYPE-C port4. When the USB port and TYPE-C port are plugged into the mobile phone at the same time, both ports are 5V outputSpecification: Package Weight One Package Weight 0.08kgs / 0.17lb One Package Size 10cm * 8cm * 3cm / 3.94inch * 3.15inch * 1.18inch Qty per Carton 200 Carton Weight 15.00kgs / 33.07lb Carton Size 52cm * 36cm * 37cm / 20.47inch * 14.17inch * 14.57inch Loading Container 20GP: 385 cartons * 200 pcs = 77000 pcs40HQ: 893 cartons * 200 pcs = 178600 pcs
£9.99
-
2 PCS XH-A232 Dual-Channel 20W High Power Digital Board MP3 Audio Power Amplifier Board Module, 20W Dual-channel MP3 Audio Amplifier
1. Purpose: 3 digital audio power amplifier2. Output voltage: 8-24v3. Power amplifier type: Class D4. Output power: 20w5. Output impedance: 4-8 ohms6. Protection: output short circuit protection, overheating protection, function self-recovery7. Module size: 43x55x14mmSpecification: Package Weight One Package Weight 0.05kgs / 0.12lb One Package Size 15cm * 10cm * 2cm / 5.91inch * 3.94inch * 0.79inch Qty per Carton 200 Carton Weight 11.00kgs / 24.25lb Carton Size 46cm * 32cm * 32cm / 18.11inch * 12.6inch * 12.6inch Loading Container 20GP: 566 cartons * 200 pcs = 113200 pcs40HQ: 1314 cartons * 200 pcs = 262800 pcs
£4.99 £1.99
-
HW-281A DC 5V 8-Channel Relay Expansion Board Module Control Panel with Indicator PLC Relay, 8-Channel Relay Module
1. Applicable to various platforms such as 51/AVR/AVR/ARM2. Using high current relay, AC250V/10A, DC30V/10A3. Independent wiring of the contact part, safe and reliable4. Standard interface, which can be expanded on various development boards5. With fixing screw holes for easy installation6. Size: 138x56x19.3mmSpecification: Package Weight One Package Weight 0.20kgs / 0.45lb One Package Size 15cm * 8cm * 2cm / 5.91inch * 3.15inch * 0.79inch Qty per Carton 100 Carton Weight 21.00kgs / 46.30lb Carton Size 46cm * 32cm * 32cm / 18.11inch * 12.6inch * 12.6inch Loading Container 20GP: 566 cartons * 100 pcs = 56600 pcs40HQ: 1314 cartons * 100 pcs = 131400 pcs
£2.99
-
SSOP20 TSSOP20 OTS-28-0.65-01 Chip Gold-Plated Dual Contact Pin Adapter Socket
1. Type: Test Block2. Working frequency: High frequency3. Application: Integrated Circuit IC4. Contact impedance: Less than 25 milliohms5. Production process: Injection molding6. Features: Fire retardant/flame retardant7. Contact material: Beryllium copper shrapnel8. Insulator material: PEI, PPS9. Number of cores: 2010. Working temperature: -65～155 degrees Celsius11. Lead spacing: 0.65mm12. Service life: 20,000 times13. Adaptation chip body width: 4.4mmFeatures:1. Using double contact technology, the contact is more stable2. The seat shell is made of special engineering plastic, which has high strength and long life.3. The shrapnel adopts imported beryllium copper material, which has low impedance and good elasticity4. Thick gold plating layer, thick contact plating, ultra-low contact impedance, high reliabilitySpecification: Package Weight One Package Weight 0.02kgs / 0.05lb One Package Size 15cm * 12cm * 6cm / 5.91inch * 4.72inch * 2.36inch Qty per Carton 200 Carton Weight 5.00kgs / 11.02lb Carton Size 52cm * 36cm * 37cm / 20.47inch * 14.17inch * 14.57inch Loading Container 20GP: 385 cartons * 200 pcs = 77000 pcs40HQ: 893 cartons * 200 pcs = 178600 pcs
£5.99
-
QFN44-0.5 Flip Shrapnel Burn Socket Test Socket Programmer, QFN44-0.5
1. Number of cores: 442. Features: U-shaped thimble, more stable contact3. Purpose: Programming socket, test socket, test, read and write on QFN44 IC chip4. Working frequency: High frequency5. Production process: Injection molding6. Application: Integrated Circuit IC7. Contact material: Beryllium copper shrapnel8. Insulator material: PPS/PET9. Chip size: 7x7cm10. Pin spacing: 0.5mmSpecification: Package Weight One Package Weight 0.02kgs / 0.05lb One Package Size 15cm * 12cm * 6cm / 5.91inch * 4.72inch * 2.36inch Qty per Carton 200 Carton Weight 5.00kgs / 11.02lb Carton Size 52cm * 32cm * 32cm / 20.47inch * 12.6inch * 12.6inch Loading Container 20GP: 500 cartons * 200 pcs = 100000 pcs40HQ: 1162 cartons * 200 pcs = 232400 pcs
£47.99
-
QFP48-0.5 QFP48 To DIP48 Burning Seat Test Seat Programming Seat, QFP48-0.5
1. Product use: Programming socket, test socket, programming and testing of QFP48 IC chips2. Applicable packages: QFP48, PQFP48, QFP48, pin pitch 0.5 mm3. Features: All pins are led out in the order of the chip4. Pin spacing: 0.5 mm5. Foot position: 486. Chip size: 7x7 mm (with pins 9x9 mm)Specification: Package Weight One Package Weight 0.07kgs / 0.15lb One Package Size 13cm * 10cm * 5cm / 5.12inch * 3.94inch * 1.97inch Qty per Carton 500 Carton Weight 15.00kgs / 33.07lb Carton Size 52cm * 37cm * 22cm / 20.47inch * 14.57inch * 8.66inch Loading Container 20GP: 630 cartons * 500 pcs = 315000 pcs40HQ: 1462 cartons * 500 pcs = 731000 pcs
£26.99
-
EMCP162/168 Flip Shrapnel To USB Test Socket EMCP Programming Socket Mobile Phone Font Read-Write Socket
1. Type: test block2. Working frequency: high frequency3. Application: integrated circuit IC4. Interface type: terminal5. Production process: injection molding6. Features: stable testing7. Contact material: beryllium copper shrapnel8. Insulator material: PET9. Number of cores: 1710. Purpose: programming socket, test socket, for testing, reading and writing of EMCP IC chips11. Lead spacing: 0.5mm12. Service life: 100,000 timesTesting method:1. Select the limit frame that matches the IC, and place the IC flat in the SOCKET according to the direction2. Plug the USB cable into the USB port of the computer, turn on the power switch of the socket, and select the corresponding test programFeatures:1. Also compatible with 186-FBGA 162-FBGA2. The shrapnel is made of imported beryllium copper by high-precision die stamping, and the head-shaped probe is designed to be hardened and thickened in the later stage to ensure product stability and durability.3. Support hot plugging and separate power switch, support for testing through the USB interface or through the connection with the board on the board corresponding to the PIN4. Using floating board structure, precise positioning, convenient IC picking and placement, higher work efficiency5. The test board is welded to the adapter board, the test socket does not need to be soldered, and the pinholes are inserted into the adapter boardSpecification: Package Weight One Package Weight 0.05kgs / 0.12lb One Package Size 13cm * 10cm * 6cm / 5.12inch * 3.94inch * 2.36inch Qty per Carton 100 Carton Weight 6.00kgs / 13.23lb Carton Size 52cm * 28cm * 52cm / 20.47inch * 11.02inch * 20.47inch Loading Container 20GP: 352 cartons * 100 pcs = 35200 pcs40HQ: 817 cartons * 100 pcs = 81700 pcs
£90.99
-
EMCP221 Flip Shrapnel To USB Test Socket Burn Socket
1. Type: Test block2. Working frequency: High frequency3. Application: integrated circuit IC4. Interface type: Terminal5. Production process: Injection molding6. Features: Stable testing7. Contact material: Beryllium copper shrapnel8. Insulator material: PET9. Number of cores: 3810. Purpose: Programming socket, test socket, to test, read and write the IC chip of EMCP22111. Lead spacing: 0.5mm12. Service life: 100,000 times13. Chip size: 11.5x13cmTesting Method:1. Select the limit frame that matches the IC, and place the IC flat in the SOCKET according to the direction2. Plug the USB cable into the USB port of the computer, turn on the power switch of the socket, and select the corresponding test programFeatures:1. Also compatible with 186-FBGA 162-FBGA2. The shrapnel is made of imported beryllium copper by high-precision die stamping, and the head-shaped probe is designed to be hardened and thickened in the later stage to ensure product stability and durability.3. Support hot plugging and separate power switch, support for testing through USB interface or connection with the board on the board according to the PIN4. Using floating board structure, precise positioning, convenient IC picking and placement, higher work efficiency5. The test board is welded to the adapter board, the test socket does not need to be soldered, and the pinholes are inserted into the adapter boardSpecification: Package Weight One Package Weight 0.05kgs / 0.12lb One Package Size 15cm * 12cm * 6cm / 5.91inch * 4.72inch * 2.36inch Qty per Carton 500 Carton Weight 27.00kgs / 59.52lb Carton Size 50cm * 50cm * 54cm / 19.69inch * 19.69inch * 21.26inch Loading Container 20GP: 197 cartons * 500 pcs = 98500 pcs40HQ: 458 cartons * 500 pcs = 229000 pcs
£91.99
-
QFN32-0.5 Burning Seat Chip Test Seat Flip Shrapnel Double-Layer Board Programming Seat, QFN32-0.5
1. Working frequency: high frequency2. Application range: integrated circuit IC3. Production process: injection molding4. Contact material: beryllium copper shrapnel5. Insulator material: PPS PET6. Number of cores: 327. Name: QFN32 flip shrapnel to 152 test seat8. Purpose: programming socket and test socket, to program and test QFN32 IC chips9. Chip size: 5x5cm10. Pin spacing: 0.5mmSpecification: Package Weight One Package Weight 0.06kgs / 0.12lb One Package Size 8cm * 8cm * 2cm / 3.15inch * 3.15inch * 0.79inch Qty per Carton 500 Carton Weight 26.00kgs / 57.32lb Carton Size 50cm * 50cm * 52cm / 19.69inch * 19.69inch * 20.47inch Loading Container 20GP: 205 cartons * 500 pcs = 102500 pcs40HQ: 476 cartons * 500 pcs = 238000 pcs
£42.99
-
Aluminum Heat Sink Cooling for Chip IC LED Transistor Power Memory, Size: 150x60x25mm
Feature1. This aluminum heat sink is to cool down the board and make it operate safely2. Reducing the risk of hardware failure because of overheating. Various MOS tube3. Electronic Audio and Video, converter, circuit board, Power IC, Transistor etcSpecification1. Quantity of blade: 242. Material: Aluminum3. Color: Silver4. Blade thickness: 1mm5. Base plate thickness: 2mm6. Size: 150 x 60 x 25mm7. Package included:- 1 x Aluminum heat sink 150 x 60 x 25mmSpecification: Package Weight One Package Weight 0.22kgs / 0.47lb One Package Size 15cm * 6cm * 3cm / 5.91inch * 2.36inch * 1.18inch Qty per Carton 79 Carton Weight 15.00kgs / 33.07lb Carton Size 30cm * 50cm * 50cm / 11.81inch * 19.69inch * 19.69inch Loading Container 20GP: 355 cartons * 79 pcs = 28045 pcs40HQ: 825 cartons * 79 pcs = 65175 pcs
£4.99 £1.99
-
Waveshare Waveshare For Raspberry Pi Pico CAN Bus Module (B),Enabling Long Range Communication Through SPI,23775, 23775
1. Suitable for Raspberry Pi Pico and other devices to achieve reliable remote communication2. Standard Raspberry Pi Pico header supports Raspberry Pi Pico series boards.3. Features CAN function, adopts SPL interface CAN controller MCP2515 with transceiver SIT65HVD230DR4. Comes with online development resources and manual (Raspberry Pi Pico C/C++ and MicroPvthon examples)l5. Operating voltage: 3.3V-5V6. CAN controller: RMCP25157. CAN transceiver: SIT65HVD230DR8. Communication bus: SPI9. Baudrate: 5K-1000Kbps10. Size: 52 x 21mmSpecification: Package Weight One Package Weight 0.02kgs / 0.05lb One Package Size 8cm * 5cm * 3cm / 3.15inch * 1.97inch * 1.18inch Qty per Carton 500 Carton Weight 12.00kgs / 26.46lb Carton Size 30cm * 50cm * 40cm / 11.81inch * 19.69inch * 15.75inch Loading Container 20GP: 444 cartons * 500 pcs = 222000 pcs40HQ: 1031 cartons * 500 pcs = 515500 pcs
£12.99
-
Waveshare Waveshare 24019 Flexible And Expandable Off-Road Tracked UGV, Multiple Hosts Support, With External Rails and ESP32 Slave Computer, Waveshare 24019
1. Dimensions: 231x197x151mm2. Suspension system: 4×2 (independent)3. Chassis height: 26mm4. Guide rail center distance: 170mm5. Track width: 44mm6. Running speed: 0.25~1m/s7. Track horizontal ground length (no load): 115mm8. Suspension material: 1.5mm (thickness) stainless steel9. Track climbing ground length (with large load): 170 mm10. Body material: 2 mm (thickness) 5052 aluminum alloy11. Weight: 1.9 kg12. Vertical obstacle clearance capability: 40mm13. Driving Payload: 6.2kg14. Climbing ability: 36 degrees15. Battery holder: 18650 lithium battery x 3 (not included)16. Turning radius (min): 0 meters (rotating in place)17. Charging time: 1.5 hours18. Battery life: 1 hour (full power continuous output)19. Motor power: 5.2W×220. Remote control function: WIFI, AP/STA21. Motor encoder: basic pulse 11PPR22. Communication interface: UART/serial bus servo interface/IIC23. The crawler-type mobile robot chassis has super off-road crossing ability and anti-seismic performance, and all codes are open source for secondary development24. Support multiple host computers, can communicate with ESP32 slaves through the serial port25. Motors with encoders can get speed feedback for closed-loop speed control26. Built-in 3S UPS power supply module, supports 3 18650 lithium batteries (serial connection, not included), provides uninterrupted power supply for the robot, and supports charging and power output at the same time27. Built-in multifunctional robot driver board, based on ESP32, onboard WIFI and Bluetooth, used to drive serial bus servos, output PWM signals, expand TF card slots, etc.28. Multiple independent suspension systems are used to greatly reduce the impact of complex terrain and easily meet the needs of heavy loads, shock absorption, and off-road29. And it comes with 2x 1020 European standard profile guide rails, providing more possibilities for secondary developmentSpecification: Package Weight One Package Weight 2.00kgs / 4.42lb One Package Size 23cm * 23cm * 14cm / 9.06inch * 9.06inch * 5.51inch Qty per Carton 14 Carton Weight 30.00kgs / 66.14lb Carton Size 56cm * 56cm * 34cm / 22.05inch * 22.05inch * 13.39inch Loading Container 20GP: 250 cartons * 14 pcs = 3500 pcs40HQ: 580 cartons * 14 pcs = 8120 pcs
£163.99
-
Waveshare Waveshare Flexible RGB Full-color LED Matrix Panel, 2.5mm Pitch, 96x48 Pixels, Adjustable Brightness Bendable PCB, 23709
1. Pixel: 96 x 48=4608 dots2. Pitch: 2.5mm3. Pixel format: 1R1G1B4. Viewing angle: greater than 140 degrees5. Control mode: synchronous6. Drive: 1/16 scan7. Connector: HUB758. Power supply: 5V / 2.5A (VH4 connector input)9. Power: within 20W10. Size: 24 x 12cmFeatures:1. 4608 independent RGB led, full color display, brightness adjustable2. 96x48 pixels, 2.5mm pitch, allows displaying text, color image or animation3. 240x120mm size, moderate size, suitable for DIY desktop display or wall mount display4. Two HUB75 headers on board, 1 for controller data input, 1 output, chain support5. Flexible PCB material, can be gently bent, suitable for some application scenarios such as cylinders, spheres and other curved surfaces6. Provide open source development resources (for Raspberry Pi / Raspberry Pi Pico / ESP32 / Arduino, etc.)Specification: Package Weight One Package Weight 0.38kgs / 0.83lb One Package Size 26cm * 14cm * 2cm / 10.24inch * 5.51inch * 0.79inch Qty per Carton 66 Carton Weight 30.00kgs / 66.14lb Carton Size 50cm * 50cm * 60cm / 19.69inch * 19.69inch * 23.62inch Loading Container 20GP: 177 cartons * 66 pcs = 11682 pcs40HQ: 412 cartons * 66 pcs = 27192 pcs
£24.99
-
Waveshare Waveshare RGB Full-color LED Matrix Panel, 2.5mm Pitch, 64x32 Pixels, Adjustable Brightness, 23707, 23707
1. Pixel: 64 x 32=2048 dots2. Pitch: 2.5mm3. Pixel format: 1R1G1B4. Viewing angle: greater than 140 degrees5. Control mode: synchronous6. Drive: 1/16 scan7. Connector: HUB758. Power supply: V / 2.5A (VH4 connector input)9. Power: within 12W10. Size: 16 x 8cmFeatures:1. 2048 independent RGB led, full color display, adjustable brightness2. 64x32 pixels, 2.5mm pitch, allows displaying text, color images or animations 3. 160x80mm size, moderate size, suitable for DIY desktop display or wall mount display4. Two HUB75 headers on board, 1 for controller data input, 1 output, chain support5. Provide open source development resources (for Raspberry Pi / Raspberry Pi Pico / ESP32 / Arduino, etc.)Specification: Package Weight One Package Weight 0.40kgs / 0.89lb One Package Size 20cm * 10cm * 2cm / 7.87inch * 3.94inch * 0.79inch Qty per Carton 74 Carton Weight 30.00kgs / 66.14lb Carton Size 50cm * 50cm * 60cm / 19.69inch * 19.69inch * 23.62inch Loading Container 20GP: 177 cartons * 74 pcs = 13098 pcs40HQ: 412 cartons * 74 pcs = 30488 pcs
£16.99
-
HW-318 12V To 5V Buck Module DC-DC 3A DC Power Module LED Battery Car Voltmeter
1. Two-wire car voltmeter + 5.0V USB charging combo2. High-performance, multi-purpose, intelligent and user-friendly design3. If you don’t need to enable the switch, just disconnect the pointed line4. Ultra-wide range of voltmeter: DC4. 5~40V5. The output current capacity of 5.0V, 2A is enough to meet various USB devices, and the voltage is very stable. This module is short-circuited by D+D- by default, which is compatible with most mobile phone charging, and reserves the installation position of various mobile phone identification resistors. , If you need to add identification resistance, please cut off the wire connecting D+ D-6. Purpose: Ultra-wide input voltage, can be used for cars, battery cars, motorcycles, used to monitor the battery voltage, timely grasp the battery status, can be used for various voltage measurement purposes7. Note: The power module will become hot during normal use. If you are mindful of this heat or are sensitive to heat, please take it carefully.8. Weight: 13g9. Size: 58x21x10mmModule performance and highlights:1. The output current capacity of 5V/2A (note: when the input voltage is 6.5~40V, the output voltage of 5.0V can be stabilized)2. With reverse connection protection, reverse connection will not burn3. With over-current and over-temperature protection4. With USB power indicator5. With wiring terminals, easy to access the line6. High efficiency, low rippleModule instructions:After the module is powered on, the voltage can be detected in real time. When you need to charge mobile phones, Ipads, MP3s and other digital products, just touch the "output enable" button. At this time, the USB power indicator lights up and the USB outputs 5.0V voltage; When you need to turn off the digital tube, touch the "low power consumption" button, and the module enters the ultra-low power standby mode, and the USB output is also turned off accordingly.Specification: Package Weight One Package Weight 0.03kgs / 0.07lb One Package Size 8cm * 5cm * 3cm / 3.15inch * 1.97inch * 1.18inch Qty per Carton 300 Carton Weight 10.00kgs / 22.05lb Carton Size 42cm * 32cm * 32cm / 16.54inch * 12.6inch * 12.6inch Loading Container 20GP: 620 cartons * 300 pcs = 186000 pcs40HQ: 1439 cartons * 300 pcs = 431700 pcs
£4.99 £1.99
-
Waveshare Waveshare Raspberry Pi Camera Module, Embedded IR-CUT, Supports Night Vision, Type B
Features1. Raspberry Pi camera, supports all revisions of the Pi2. Embedded removable IR-CUT filter, eliminating color distortion in the daylight3. Comes with infrared LED, supports night vision4. 5 megapixel OV5647 sensor5. Adjustable focus distance6. Camera specifications- CCD size: 1/4 inch- Aperture (F): 1.2- Focal Length: 8mm- Angle of View (diagonal): 40 degree- Sensor best resolution: 1080p7. 4 screw holes- Used for attachment- Provides 3.3V power output- Supports connecting infrared LED and/or fill flash LED8. Dimension: 31mm x32mmNote: To use the camera with Raspberry Pi Zero / Zero W / Zero WH, you need to buy a specific cable: Raspberry Pi Zero v1.3 Camera CableNote: The actual image pixels is 5MP, which depends on the sensor, so it doesnt matter that there is a 3MP silk mark on the camera.Package Contents1. RPi IR-CUT Camera (B) x12. Infrared LED Board (B) x23. 15-pin FFC (opposite sides contact) x1Specification: Package Weight One Package Weight 0.07kgs / 0.14lb One Package Size 6cm * 6cm * 2cm / 2.36inch * 2.36inch * 0.79inch Qty per Carton 720 Carton Weight 15.00kgs / 33.07lb Carton Size 36cm * 36cm * 40cm / 14.17inch * 14.17inch * 15.75inch Loading Container 20GP: 514 cartons * 720 pcs = 370080 pcs40HQ: 1194 cartons * 720 pcs = 859680 pcs
£19.99
-
Waveshare Waveshare High-Torque Serial Bus Servo, Desktop Robotic Arm Kit, Based On ESP32, 5-DOF, US Plug, EU Plug, UK Plug
1. RoArm-M1 is a serial robotic arm with a total of 5 degrees of freedom, including the gripping degree of freedom of the gripper2. Two control methods in the demonstration: angle control and coordinate control3. Support Leading-following mode based on ESP-NOW4. Support motion recording and playback control mode5. Based on ESP32, it supports WIFI and UART communication, and provides a variety of motion model demos and cross-platform web applications6. Support multiple host computers and provide rich learning resources such as ROS 2 demo7. Weight: 1.894 kgPacking list:-RoArm-M1 robotic arm x 1-Adapter x 1Specification: Package Weight One Package Weight 1.95kgs / 4.31lb One Package Size 35cm * 15cm * 20cm / 13.78inch * 5.91inch * 7.87inch Qty per Carton 14 Carton Weight 30.00kgs / 66.14lb Carton Size 50cm * 50cm * 60cm / 19.69inch * 19.69inch * 23.62inch Loading Container 20GP: 177 cartons * 14 pcs = 2478 pcs40HQ: 412 cartons * 14 pcs = 5768 pcs
£259.99 - £260.99
-
Waveshare Atmel-ICE-C Kit Original PCBA Inside Full Functionality Cost Effective Development Tool for Atmel SAM / AVR Microcontrollers
Overview 1. Atmel-ICE-C is the cost effective solution for the powerful Atmel-ICE, it adopts the original ATMEL-ICE-PCBA and comes with a durable aluminium alloy enclosure. 2. Atmel-ICE-C delivers the same functionality and usability just as the ATMEL-ICE Full Kit, it is capable of debugging and programming Atmel ARM Cortex -M based Atmel SAM and AVR microcontrollers with on-chip debug capability. Key Features 1. Support JTAG, SWD, PDI, TPI, aWire, SPI and debugWIRE interfaces 2. Full source-level debugging in Atmel Studio 3. Support all built-in hardware breakpoints in the target microcontroller (number depends on the OCD module in the target) 4. Up to 128 software breakpoints 5. 1.62 to 5.5V target operation 6. USB powered 7. Provides both ARM Cortex Debug Connector (10-pin) pin-out and AVR JTAG connector pin-out Supported Software 1. Support Atmel Studio 6.2 or higher version 2. Directly supports ICC8AVR or higher version 3. Support programming HEX files generated by ICCAVR, CVAVR, IAR, etc. Supported Devices 1. Programming and on-chip debugging of all Atmel AVR 32-bit MCUs on both JTAG and aWire interfaces 2. Programming and on-chip debugging of all Atmel AVR XMEGA family devices on both JTAG and PDI 2-wire interfaces 3. JTAG and SPI programming and debugging of all Atmel AVR 8-bit MCUs with OCD support on either JTAG or debugWIRE interfaces 4. Programming and debugging of all Atmel SAM ARM Cortex-M based MCUs on both SWD and JTAG interfaces 5. Programming of all Atmel tinyAVR 8-bit MCUs with support for the TPI interface 6. For more details, please visit UC3, Mega, SAM , Tiny, Xmega Specifications 1. INTERFACE VOLTAGE: 1.62V ~ 5.5V 2. JTAG CLOCK: 32kHz ~ 7.5MHz 3. PDI CLOCK: 32kHz ~ 7.5MHz 4. DEBUGWIRE BAUDRATE: 4kbit/s ~ 0.5Mbit/s 5. AWIRE BAUDRATE: 7.5kbit/s ~ 7Mbit/s 6. SPI CLOCK: 8kHz ~ 5MHz 7. SWD CLOCK: 32kHz ~ 2MHz 8. PC INTERFACE: USB 2.0 high speed Package list 1. Atmel-ICE-C unit x1 2. USB type A plug to micro B plug cable x1 3. IDC flat cable with 10-pin 50-mil connector and 6-pin 100-mil connector x1 4. Multi-functional adapter board x1 5. 10pin flat cable x1 6. 10pin 100mil squid cable x1 7. 6-pin to 10-pin ISP cable x1Specification: Package Weight One Package Weight 0.15kgs / 0.33lb One Package Size 16cm * 10cm * 4cm / 6.3inch * 3.94inch * 1.57inch Qty per Carton 120 Carton Weight 15.00kgs / 33.07lb Carton Size 48cm * 40cm * 40cm / 18.9inch * 15.75inch * 15.75inch Loading Container 20GP: 347 cartons * 120 pcs = 41640 pcs40HQ: 806 cartons * 120 pcs = 96720 pcs
£135.99
-
Waveshare JetBot AI Kit Accessories, Add-ons for Jetson Nano to Build JetBot, US Plug, Add-ons for Jetson Nano
Overview1. Smart robot is always the favorite project of electronic enthusiasts, however, a robot will be "not that smart" if it is not AI-based.2. Welcome the JetBot, an actual smart robot powered by Jetson Nano. With the intelligent eye (front camera), facial recognition, object tracking, auto line following, and collision avoidance can be easily achieved. It also comes with ROS nodes code, which makes it easy to get started with the open source ROS (Robot Operating System), and to learn the system framework and concepts of ROS.3. If you have got a Jetson Nano on your desk right now, combined with our open source codes and tutorials, these add-ons would be the ideal choice for you to learn AI robot designing and development.Features1. Adopts 3x 18650 batteries (NOT included), high battery capacity, up to 12.6V voltage output, more powerful driving force.2. Integrates S-8254AA + AO4407A lithium battery protection circuit, provides protections for over-charge, over-discharge, over-current, and short circuit.3. Onboard APW7313 voltage regulator, provides stable 5V voltage for the Jetson Nano.4. Onboard TB6612FNG dual H-bridge motor driver.5. Onboard 0.91inch 128×32 pixels OLED, allows to display robot IP address, RAM, battery life, etc.6. Onboard ADS1115 AD acquisition chip for monitoring the battery in real time.7. Weight: 773gWhat is on the JetBot Expansion Board1. S-8254AA: Lithium battery protector, provides protections for over-charge, over-discharge, over-current, and short circuit2. ADS1115: 16-bit AD acquisition chip, monitoring the battery in real time3. AO4407A:: P-Channel MOSFET for protection circuit4. APW7313:: 5V power regulator for powering the Jetson Nano5. PCA9685: PWM controller, I2C interface, for IO expansion6. TB6612FNG: dual H-bridge motor driver7. 0.91inch OLED: SSD1306 driver chip, 128×32 pixels8. Battery charger input: charging the 3x 18650 batteries9. Power switch10. 18650 battery holder11. Motor connector (bottom side)12. Jetson Nano communication header: I2C interface and power supplyPacking List1. Metal box x12. Camera holder x13. Acrylic piece x14. Jetbot expansion board x15. IMX219-160 Camera x16. Wireless-AC8265 x17. Motor 2PCS x18. Wheel 2PCS x19. Omni-direction wheel 2PCS x110. Power adapter EU head x111. 12.6V battery charger x112. Wireless gamepad x113. Screwdriver 2PCS x114. 6Pin 9cm cable x115. Screws pack x116. Spanner x117. Cooling fan x118. Micro SD card reader x1Specification: Package Weight One Package Weight 1.04kgs / 2.30lb One Package Size 22cm * 16cm * 4cm / 8.66inch * 6.3inch * 1.57inch Qty per Carton 20 Carton Weight 21.50kgs / 47.40lb Carton Size 62cm * 42cm * 42cm / 24.41inch * 16.54inch * 16.54inch Loading Container 20GP: 243 cartons * 20 pcs = 4860 pcs40HQ: 566 cartons * 20 pcs = 11320 pcs
£78.99
-
Waveshare Waveshare JetBot AI Kit, AI Robot Based on Jetson Nano, Based on Jetson Nano
OverviewSmart robot is always the favorite project of electronic enthusiasts, however, a robot will be "not that smart" if it is not AI-based.Welcome the JetBot, an actual smart robot powered by Jetson Nano. With the intelligent eye (front camera), facial recognition, object tracking, auto line following, and collision avoidance can be easily achieved. It also comes with ROS nodes code, which makes it easy to get started with the open source ROS (Robot Operating System), and to learn the system framework and concepts of ROS.Features1. Adopts 3x 18650 batteries (NOT included), high battery capacity, up to 12.6V voltage output, more powerful driving force.2. Integrates S-8254AA + AO4407A lithium battery protection circuit, provides protections for over-charge, over-discharge, over-current, and short circuit.3. Onboard APW7313 voltage regulator, provides stable 5V voltage for the Jetson Nano.4. Onboard TB6612FNG dual H-bridge motor driver.5. Onboard 0.91inch 128×32 pixels OLED, allows to display robot IP address, RAM, battery life, etc.6. Onboard ADS1115 AD acquisition chip for monitoring the battery in real time.7. Weight: 1029gWhat is on the JetBot Expansion Board1. S-8254AA: Lithium battery protector, provides protections for over-charge, over-discharge, over-current, and short circuit2. ADS1115: 16-bit AD acquisition chip, monitoring the battery in real time3. AO4407A: P-Channel MOSFET for protection circuit4. APW7313: 5V power regulator for powering the Jetson Nano5. PCA9685: PWM controller, I2C interface, for IO expansion6. TB6612FNG: dual H-bridge motor driver7. 0.91 inch OLED: SSD1306 driver chip, 128×32 pixels8. Battery charger input: charging the 3x 18650 batteries9. Power switch10. 18650 battery holder11. Motor connector (bottom side)12. Jetson Nano communication header: I2C interface and power supplyPacking List1. Jetson Nano Developer Kit x12. Micro SD Card 64GB ×13. Metal box x14. Camera holder x15.Acrylic piece x16. Jetbot expansion board x17. IMX219-160 Camera x18. Wireless-AC8265 x19. Motor 2PCS x110. Wheel 2PCS x111.Omni-direction wheel 2PCS x112. Power adapter EU head x113. 12.6V battery charger x114. Wireless gamepad x115. Screwdriver 2PCS x116. 6Pin 9cm cable x117. Screws pack x118. Spanner x119. Cooling fan x120. Micro SD card reader x1Specification: Package Weight One Package Weight 1.40kgs / 3.10lb One Package Size 28cm * 20cm * 15cm / 11.02inch * 7.87inch * 5.91inch Qty per Carton 10 Carton Weight 15.00kgs / 33.07lb Carton Size 52cm * 40cm * 60cm / 20.47inch * 15.75inch * 23.62inch Loading Container 20GP: 213 cartons * 10 pcs = 2130 pcs40HQ: 496 cartons * 10 pcs = 4960 pcs
£262.99
-
Waveshare Waveshare 4-DOF Metal Robot Arm Kit for Raspberry Pi (Europe), Bluetooth / WiFi Remote Control, EU Plug
Overview1. Equip your Raspberry Pi with this 4-DOF metal robot arm, and get started to explore the world of artificial intelligent robotic.2. This starter robotic arm kit includes: servo driver HAT, metal mechanical arm structure, and 4x metal gear servos. When used with the Raspberry Pi, it is easy to control the arm by smart phone through Bluetooth or WiFi connection.The Servo DriverAdopts Servo Driver HAT:1. Raspberry Pi connectivity, compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+, Jetson Nano2. I2C controlled, using only 2 pins3. Up to 16-Channel servo/PWM outputs, 12-bit resolution for each channel (4096 scales)4. Integrates 5V regulator, up to 3A output current, can be powered from battery through VIN terminal5. Standard servo interface, supports common used servo such as SG90, MG90S, MG996R, etc.6. Reserved I2C control pins, allows to work with other control boards7. Comes with development resources and manual (examples in python like Bluetooth/WiFi remote control)The Robot Arm Structure1. 4-DOF, large solid base, metal mechanical grasper2. Full aluminium alloy body, sandblasting oxidation surface, strong & durable3. Clever mechanical structure and mounting design, agile to control, easy to build4. Fitted with 4x metal gear servos (1x MG996R, 3x MG90S), large torque force, smooth movingPackage ContentsNote: Raspberry Pi is NOT included.1. Metal arm parts x12. MG996R Servo x13. MG90S Servo x34. MG996R servo wheel x15. Servo Driver HAT x16. Power adapter EU standard USB output x17. Servo extension wire 150mm x18. Screws pack x19. Screwdrivers 2PCS x1Specification: Package Weight One Package Weight 0.48kgs / 1.06lb One Package Size 25cm * 15cm * 8cm / 9.84inch * 5.91inch * 3.15inch Qty per Carton 20 Carton Weight 9.60kgs / 21.16lb Carton Size 50cm * 30cm * 40cm / 19.69inch * 11.81inch * 15.75inch Loading Container 20GP: 444 cartons * 20 pcs = 8880 pcs40HQ: 1031 cartons * 20 pcs = 20620 pcs
£41.99
Sie haben 192 von 251 Produkten gesehen