Résultats de la recherche pour "DC Connector Accessories"

Why to use1. Cell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save life of somebody. 2. Unfortunately, there are still some places where one can find themselves out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: 1) Parking lots, tunnels 2) Big stores, office buildings 3) Cars, boats etc. 4) House in remote areas etcFeatures1. High-gain linear power amplifier 2. ALC and AGC function technology 3. Ultra-low noise receive amplifier 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications 7. With full-duplex communication mode. 8. Dispel the heat effective reasonable, the structure is pretty, the volume is suitableHow to work1. The outside antenna catches the low signal from the mobile base station and delivers it to the cell phone amplifier through the connection cable (coax). 2. After the signal is accepted by the phone amplifier, the device amplifies it. 3. Then this amplified signal goes through the connection cable (coax) to the inside antenna. 4. And after that, the amplified signal transmits to the cell phoneHow to install1. Step 1: Use your mobile phone to test signal strength outside house or on roof, -70dbm is the basic requirement (full bar). 2. Step 2: Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Step 3: Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Step 4: Mount your indoor antenna with signal repeater 5. Step 5: Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signalNotes1. Connect outdoor (BTS) port with outdoor antenna, connect indoor ANT(MS) port with indoor antenna, outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away from each other at least. 2. Indoor and outdoor antenna must be separated by wallTechnique supports1. If still weak signal receipt after installation, please check if outdoor antenna point to signal tower correctly or elsewhere has stronger signal and confirm signal strength achieve-70DBM. 2. If still have no signal after installation, please check our device power adapter whether connected perfectly? And connectors connect well. 3. If strength is not steady, please check if outdoor and indoor antenna is too close; please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 4. Packed the outdoor connector by waterproof glue, otherwise wet reduce the signal cover areaSpecification: General Frequency Range WCDMA 2100MHz, Uplink 1920-1980MHz, Downlink 2110-2170MHz Gain Uplink 53-57dB, Downlink 58-62dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC: 100~240V, 50/ 60Hz; DC: 5V 2A Power Consumption <5W RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 100mm x 45mm x 18mm Weight 350g Package Include Package Contents 1 x 12dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 5m RG6-50 OHM Indoor Coaxial Cable 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 1.59kgs / 3.51lb One Package Size 51cm * 18cm * 13cm / 20.08inch * 7.09inch * 5.12inch Qty per Carton 4 Carton Weight 5.75kgs / 12.67lb Carton Size 53cm * 38cm * 28cm / 20.87inch * 14.96inch * 11.02inch Loading Container 20GP: 472 cartons * 4 pcs = 1888 pcs40HQ: 1097 cartons * 4 pcs = 4388 pcs

Lis Plus Moins

About The Product1. VAR11N-300 is the professional Mini WiFi repeater, and together with mini WiFi router and WiFi intelligent bridge that is elaborately developed by HouTian Network, the original creation D/A temperature compensated auto frequency control technology (TAFC), it solves the common failing of the traditional WiFi router or WiFi products that easily drop the network, the lasting stability ensure that the WiFi signal is not dropped. It is as an ecology and safe WiFi repeater. It is different from the traditional method that use increased the wireless transmitter power (it will generate a strong harmful radiation) to expand the distance of wireless transmission, but in WiFi signal coverage of failure point, place this device as a WiFi signal repeater to re-enlarge the weak WiFi signal, and during not increasing the wireless transmitter power, expand WiFi signal coverage, safe and ecology, it is very useful for home or office safe WiFi signal coverage. 2. VAR11N-300 is a plug and play Mini WiFi router and WiFi bridge. On business trip and traveling stay at hotel, you just connect the Ethernet cable in the hotel room to Ethernet port of VAR11N-300, then connect power supply, the whole room is Wi-Fi wireless coverage. Now, you can take out your mobile phone, PAD and other devices that support Wi-Fi, then get Wireless internet at anywhere of the room, no need any settings.Features1. Adopt the original creation D/A temperature compensated auto frequency control technology (TAFC), the lasting stability ensure that the WiFi signal is not dropped 2. Original creation VDNS virtual domain configuration technology solves the user's trouble of configuration. 3. The smallest WiFi router, its size is less than one-half of the Bank card, very useful for both business trip and household. 4. Supply power by USB (DC 5V) 5. Low power, the whole power supply less than 4W. 6. Dedicated power supply cable together with Ethernet cable two in one cable connector, reduce redundant connector, convenient for usage. 7. In WiFi intelligent bridge mode, it can intelligent control the device WiFi mode: - WiFi AP Client (it can be used for access from WiFi to wired Ethernet) - WiFi Hotspot (it is suitable for hotel room usage) - WiFi Repeater (it can extend the distance of WiFi signal coverage, ecology and safe) 8. In WiFi intelligent bridge mode, it supports WiFi hot spot scan automatically and WiFi hot spot memory function. 9. 1 WAN, 1 LAN, two ports can interchangeable, such small volume has two ports, so unusual. 10. Support 802.11N WiFi transfer protocol, 300Mbps rate of transmission 11. Good compatibility, almost compatible with all of the smart phone, tablet computer, notebook and WiFi devices.Specification: General Model VAP11N-300 Types Repeater Material ABS Input Voltage 5V Interface USB 2.0, RJ45 Transmission Rate 300Mbps for WiFi Operation Modes Bridge mode, Repeater, AP, Router, Client Antenna Types Built-in Intelligent Omnidirectional antenna Standards WiFi IEEE 802.11n Size 44*44*14mm Weight 65g Package Weight One Package Weight 0.11kgs / 0.24lb One Package Size 10cm * 10cm * 3cm / 3.94inch * 3.94inch * 1.18inch Qty per Carton 100 Carton Weight 9.00kgs / 19.84lb Carton Size 50cm * 25cm * 21cm / 19.69inch * 9.84inch * 8.27inch Loading Container 20GP: 1015 cartons * 100 pcs = 101500 pcs40HQ: 2358 cartons * 100 pcs = 235800 pcs

Lis Plus Moins

1. High resolution, high speed transmission response. Surface hardness treatment to reduce scratches, scratches and anti-chemical treatment. With smooth and matte treatment. One calibration, high stability, never drift. 2. Screen structure: ITO Film and ITO Glass are bonded together, separated by DOT points in the middle 3. Connector: 2.54mm pitch socket, standard AMP87499-9 4. Touch media: fingers, gloved hands, pens, credit cards, etc. 5. Screen thickness: 1mm-5mm 6. OE: BHP1611J0D 7. Resolution: 4096x4096 8. Response time: less than 8 milliseconds (finger input) 9. Touch strength: 15-40gr use silicone grease with a hardness of 600 and a diameter of 16mm 10. Conversion speed: less than 20ms 11. Position accuracy: standard deviation is less than 2mm 12. Supply voltage: DC 5V 14. Screen resistance: 200-50 Ohm (X1-X2); 200-500 Ohm (Y1-Y2) 15. Insulation resistance: greater than 20M Ohm at DC25V 16. Electrostatic protection: can withstand 20 discharges of 15 kV voltage randomly distributed on the screen surface (per IEC 801-2; 150pF and 150 Ohm) 17. Light transmittance: 75-85% (at a wavelength of 550 nanometers) 18. Working temperature: -20-60 degrees Celsius 19. Storage temperature: -25-70 degrees Celsius 20. Anti-destructive: 3-12mm optical glass is fully tempered by special process as the base material. Use 1 pound to make it fall freely to the center of the glass at a height of 130cm without breaking the glass. 21. Sealing feature: High sealing material tightly seals the filter device, frame and anti-riot glass to prevent liquid leakage 22. Working temperature: -20 degrees to 70 degrees 23. Storage temperature: -40 degrees to 85 degrees 24. Working humidity: 90%RH at 40 degree Celsius (no condensation) 25. Storage humidity: 90%RH at 40 degree Celsius (no condensation) Note: LCD display is not included, it is just a touch screen.Specification: General Compatible with Mazda: Axela Package Weight One Package Weight 0.40kgs / 0.89lb One Package Size 29cm * 19cm * 4cm / 11.42inch * 7.48inch * 1.57inch Qty per Carton 20 Carton Weight 9.50kgs / 20.94lb Carton Size 42cm * 38cm * 32cm / 16.54inch * 14.96inch * 12.6inch Loading Container 20GP: 522 cartons * 20 pcs = 10440 pcs40HQ: 1212 cartons * 20 pcs = 24240 pcs

Lis Plus Moins

Features1. Supports 6 safe driving modes. By using the matching control harness, you can switch the mode you need at will through the switch, providing a clear view in any complex environment.2. Made of thick aviation aluminum for CNC manufacturing, it has super high hardness and corrosion resistance, and has stronger resistance to impact and wear. The top is equipped with a hollow protective cover to make your car more unique and different.3. The integrated design of the waterproof harness switch and the standardized waterproof connector treatment of the spotlight wiring port ensures that the spotlight has a longer service life. The built-in high-power control ballast can better stabilize the voltage and current, reduce the probability of spotlight flickering or directly connect the original car battery for too long, resulting in power loss and other problems.4. The die-cast aluminum shell has the strength and durability to withstand harsh environments. The special design of the bifocal shape of the improved bifocal lens helps to refract and focus light, significantly improving the focusing effect. It can last for 50,000 hours, with an IP68 protection level, waterproof, dustproof, shockproof, and corrosion-resistant, and is not afraid of harsh environments.5. The mounting bracket can be adjusted 180 degrees front and back, 360 degrees left and right, and can be installed according to the beam angle you need.6. Widely used, compatible with most motorcycles, jeeps, four-wheelers, trucks, tractors, trailers, golf carts, vans, cars, motorcycles, SUVs, ATVs. In addition, there are many indoor and outdoor uses: garden lights, backyard lights, reversing lights, high beam lights, reverse lights (DC 9-30V available).Parameters:1. Lamp beads: 6 ZES-3575 LED chips2. Light type: spotlight3. Color temperature: 6000K/4500K/3000K4. Brightness: 3000LM5. Power: 30W6. Material: aviation aluminum alloy7. Lifespan: more than 50000H8. Voltage: wide voltage 9-32V9. Working temperature: low temperature -40 degrees Celsius to high temperature 150 degrees Celsius10. Heat dissipation principle: aviation aluminum alloy fence heat dissipation, aluminum heat dissipation11. Waterproof grade: IP68Specification: Package Weight One Package Weight 0.45kgs / 1.00lb One Package Size 21cm * 14cm * 9cm / 8.27inch * 5.51inch * 3.54inch Qty per Carton 30 Carton Weight 15.00kgs / 33.07lb Carton Size 44cm * 44cm * 30cm / 17.32inch * 17.32inch * 11.81inch Loading Container 20GP: 459 cartons * 30 pcs = 13770 pcs40HQ: 1065 cartons * 30 pcs = 31950 pcs

Lis Plus Moins

1. Compatible with all HD-CVI, HD-TVI, HD-AHD. 2. Up to 300m for 720P CVI Cameras. 3. Up to 200m for 1080P CVI Cameras. 4. Up to 200m for 720P/1080p CVI Cameras. 5. Up to 300m for 720P AHD camera. 6. Up to 250m for 720P TVI camera. 7. Up to 200m for 1080P TVI Cameras. 8. NTSC, PAL, and SECAM video formats. 9. No power required. 10. 60dB cross talk and noise immunity. 11. Compact size and easy installation. 12. Built-in transient suppression protection. 13. Frequency response: DC to 60MHZ. 14. Attenuation: 0.5dB type. 15. CMRR: 60dB. 16. Impedance: BNC: 75ohms, terminal: 100ohms.Specification: General Model 202E+-HD Material Plastic, ABS Connector Types BNC Male Size 4.2*1.5*1.5cm Weight 28g Package Weight One Package Weight 0.06kgs / 0.13lb One Package Size 9.5cm * 8.2cm * 1.5cm / 3.74inch * 3.23inch * 0.59inch Qty per Carton 300 Carton Weight 14.00kgs / 30.86lb Carton Size 48cm * 34cm * 32cm / 18.9inch * 13.39inch * 12.6inch Loading Container 20GP: 510 cartons * 300 pcs = 153000 pcs40HQ: 1185 cartons * 300 pcs = 355500 pcs

Lis Plus Moins

1. High resolution, high speed transmission response. Surface hardness treatment to reduce scratches, scratches and anti-chemical treatment. With smooth and matte treatment. One calibration, high stability, never drift. 2. Screen structure: ITO Film and ITO Glass are bonded together, separated by DOT points in the middle 3. Connector: 2.54mm pitch socket, standard AMP87499-9 4. Touch media: fingers, gloved hands, pens, credit cards, etc. 5. Screen thickness: 1mm-5mm 6. OE: LQ080Y5DZ10 12 7. Resolution: 4096x4096 8. Response time: less than 8 milliseconds (finger input) 9. Touch strength: 15-40gr use silicone grease with a hardness of 600 and a diameter of 16mm 10. Conversion speed: less than 20ms 11. Position accuracy: standard deviation is less than 2mm 12. Supply voltage: DC 5V 14. Screen resistance: 200-50 Ohm (X1-X2); 200-500 Ohm (Y1-Y2) 15. Insulation resistance: greater than 20M Ohm at DC25V 16. Electrostatic protection: can withstand 20 discharges of 15 kV voltage randomly distributed on the screen surface (per IEC 801-2; 150pF and 150 Ohm) 17. Light transmittance: 75-85% (at a wavelength of 550 nanometers) 18. Working temperature: -20-60 degrees Celsius 19. Storage temperature: -25-70 degrees Celsius 20. Anti-destructive: 3-12mm optical glass is fully tempered by special process as the base material. Use 1 pound to make it fall freely to the center of the glass at a height of 130cm without breaking the glass. 21. Sealing feature: High sealing material tightly seals the filter device, frame and anti-riot glass to prevent liquid leakage 22. Working temperature: -20 degrees to 70 degrees 23. Storage temperature: -40 degrees to 85 degrees 24. Working humidity: 90%RH at 40 degree Celsius (no condensation) 25. Storage humidity: 90%RH at 40 degree Celsius (no condensation) Note: LCD display is not included, it is just a touch screen.Specification: General Compatible with Opel: Astra Package Weight One Package Weight 0.37kgs / 0.82lb One Package Size 29cm * 19cm * 4cm / 11.42inch * 7.48inch * 1.57inch Qty per Carton 20 Carton Weight 9.50kgs / 20.94lb Carton Size 42cm * 38cm * 32cm / 16.54inch * 14.96inch * 12.6inch Loading Container 20GP: 522 cartons * 20 pcs = 10440 pcs40HQ: 1212 cartons * 20 pcs = 24240 pcs

Lis Plus Moins

1. High resolution, high speed transmission response. Surface hardness treatment to reduce scratches, scratches and anti-chemical treatment. With smooth and matte treatment. One calibration, high stability, never drift. 2. Screen structure: ITO Film and ITO Glass are bonded together, separated by DOT points in the middle 3. Connector: 2.54mm pitch socket, standard AMP87499-9 4. Touch media: fingers, gloved hands, pens, credit cards, etc. 5. Screen thickness: 1mm-5mm 6. OE: LAM070G004A GCX156AKM. Please check the OE number before placing an order.. 7. Resolution: 4096x4096 8. Response time: less than 8 milliseconds (finger input) 9. Touch strength: 15-40gr use silicone grease with a hardness of 600 and a diameter of 16mm 10. Conversion speed: less than 20ms 11. Position accuracy: standard deviation is less than 2mm 12. Supply voltage: DC 5V 14. Screen resistance: 200-50 Ohm (X1-X2); 200-500 Ohm (Y1-Y2) 15. Insulation resistance: greater than 20M Ohm at DC25V 16. Electrostatic protection: can withstand 20 discharges of 15 kV voltage randomly distributed on the screen surface (per IEC 801-2; 150pF and 150 Ohm) 17. Light transmittance: 75-85% (at a wavelength of 550 nanometers) 18. Working temperature: -20-60 degrees Celsius 19. Storage temperature: -25-70 degrees Celsius 20. Anti-destructive: 3-12mm optical glass is fully tempered by special process as the base material. Use 1 pound to make it fall freely to the center of the glass at a height of 130cm without breaking the glass. 21. Sealing feature: High sealing material tightly seals the filter device, frame and anti-riot glass to prevent liquid leakage 22. Working temperature: -20 degrees to 70 degrees 23. Storage temperature: -40 degrees to 85 degrees 24. Working humidity: 90%RH at 40 degree Celsius (no condensation) 25. Storage humidity: 90%RH at 40 degree Celsius (no condensation) Note: LCD display is not included, it is just a touch screen. Specification: General Compatible with Citroen: C5 Peugeot: 208, 308, 2008 Package Weight One Package Weight 0.21kgs / 0.46lb One Package Size 29cm * 19cm * 4cm / 11.42inch * 7.48inch * 1.57inch Qty per Carton 20 Carton Weight 7.50kgs / 16.53lb Carton Size 42cm * 38cm * 32cm / 16.54inch * 14.96inch * 12.6inch Loading Container 20GP: 522 cartons * 20 pcs = 10440 pcs40HQ: 1212 cartons * 20 pcs = 24240 pcs

Lis Plus Moins

1. Professional testing, efficient and accurate, plug and test, fast search2. Stable performance and long service life3. Fast and accurate, efficient and accurate, refuse to wait4. Split design, easy to use tester5. Anti-seismic and drop-proof, more suitable for construction site environment6. Small and convenient, easy to carry and does not take up space7. Main and auxiliary testers, split design8. Simultaneous testing, smooth connection to standard multi-port9. Transmission distance: greater than or equal to 3KM10. Host operating current: less than 10mA11. Auxiliary machine working current: less than 30mA12. Material: ABS13. Function: Network detection cable hunting14. Power supply: 9V DC laminated battery (not included in the product)15. Engine size: 140x75x30mm16. Receiver size: 220x48x32mm17. Net weight: 250g18. Gross weight: 0.4kgTelephone/network line hunting function:1. Directly plug the telephone line with crystal head into the telephone line hunting interface RJ-112. Turn the function selection switch of the transmitter to the SCAN position, the hunting indicator STATUS will flash, indicating that the transmitter is working normally3. Turn on the power switch of the receiver, and use the signal receiving head of the receiver to find the required target cable4. During the test, you can press the function switch button to switch between dual audioPower cable line hunting function:1. Connect the transmitter and the metal-finding wire through the alligator clip2. Turn the function selection switch of the transmitter to the SCAN position, the hunting indicator STATUS will flash, indicating that the transmitter is working normally3. Press the receivers jog button down, and use the receivers probe to inquire the desired target cable4. During the test, you can press the function switch button to switch between dual audioNetwork line proofreading function:1. Insert the RJ-45 connectors at both ends of the network cable to be tested into the corresponding ports of the transmitter and receiver respectively2. Turn the function selection switch of the transmitter to the TEST position, and the test indicator VERIFY will flash, indicating that the transmitter is working normally3. According to 18 line sequence indicators to judge the characteristics of line short circuit, open circuit, open circuit and crossover4. During the test, you can press the function switching button to switch between fast and slow gearsSpecification: Package Weight One Package Weight 0.48kgs / 1.05lb One Package Size 15cm * 5cm * 27cm / 5.91inch * 1.97inch * 10.63inch Qty per Carton 74 Carton Weight 30.00kgs / 66.14lb Carton Size 50cm * 50cm * 60cm / 19.69inch * 19.69inch * 23.62inch Loading Container 20GP: 177 cartons * 74 pcs = 13098 pcs40HQ: 412 cartons * 74 pcs = 30488 pcs

Lis Plus Moins

Features1. Quality chassis with track: Adopting 37-520 full-metal DC geared motor, High torque, low noise 2. 180 degree wide angle rotation, flexible controlling robotic arm 3. Quality serial bus full-metal digital servo: High torque, high precision, preventing, it from being stuck and pamaged 4. Auto collision avoidance: Collecting data via camera by taking enough images of different conditions, using the data to train the neutral network, combined With AI algorithm, achieving auto collision avoidance on sorts of environments. 5. Motion detection: Capturing moving objects on the video by motion detection 6. Color recognition and tracking: Recognizing and locking specified color by camera, and then using pan & tilt to track the specified color automatically 7. 3D coordinate system controlled robotic arm, calculated via Inverse Kinematics algorithm: Input coordinate of the target, calculating the moving angles of the 4-DOF servos by inverse kinematics algorithm, and then controlling the servos via serial bus, moving the robotic arm to reach target position 8. JupyterLab programming: JupyterLab is a web-based interactive development environment, supports multi data formats including code, document, image/video, UI control interface, etc., provides rich visualized output, allows easily creating dashboard and UI, supports flexible configuration and arrangement for modular interface. 9. 8MP 160 degree FOV camera: IMX219 sensor, 3280 x2464 resolutionPackage List1. Aluminum alloy kit x1 2. JETANK expansion board x1 3. Wireless-AC8265 with antenna x1 4. IMX219-160 Camera x1 5. Acrylic camera spacer x1 6. Camera FFC x1 7. 0.91inch OLED x1 8. 12.6V 2A power supply + additional EU head x1 9. Robotic arm gripper x1 10. Thrust bearing x1 11. Flange bearing x2 12. Coupler x2 13. Gearmotor x2 14. 5264 servo wire x1 15. Track kit (including bolt, nut, and screwdriver) x2 16. 2 x 5 Pin wire x1 17. Spanner x1 18. L-form hex socket spanner 2PCS x1 19. SCS15-AP servo x4 20. Screwdriver 2PCS x1 21. SCS15-S servo x1 22. Card reader x1 23. Mini cross wrench sleeve x2 24. Cooling fan x1 25. PH2.0 4PIN dual connector cable x1 26. Screws pack x1Specification: Package Weight One Package Weight 2.00kgs / 4.42lb One Package Size 32cm * 22cm * 16cm / 12.6inch * 8.66inch * 6.3inch Qty per Carton 8 Carton Weight 17.00kgs / 37.48lb Carton Size 65cm * 45cm * 33cm / 25.59inch * 17.72inch * 12.99inch Loading Container 20GP: 276 cartons * 8 pcs = 2208 pcs40HQ: 641 cartons * 8 pcs = 5128 pcs

Lis Plus Moins

FeaturesThis is a RS485 device data acquisitor / IoT gateway designed for industrial environment. It combines multi functions in one, including serial server, Modbus gateway, MQTT gateway, RS485 to HTTPD Client, etc. With RS485, WIFI and Ethernet ports, the module can realize functions such as serial to WIFI, serial to Ethernet, Ethernet to WIFI and so on. Using screw terminals for power input, it supports 5~36V wide range power supply. Rail-mount V0 flame-retardant case design, small in size, easy to install. It is suitable for applications like data acquisition, IoT gateway, safety & security IoT, and intelligent instrument monitoring...SpecificationsOutline: 1. Communication interface: RS485, screw terminal 2. Power supply: 5 ~ 36V DC, screw terminal 3. Case: PC + ABS, V0 flame retardant grade 4. Dimensions: L x W x H: 109.66 x 28 x 64.71 mm Comunication: 1. Ethernet: 10 / 100M auto-negotiation RJ45 connector 2. WIFI: 802.11b/g/n compliant 3. Serial port: RS485 interface (Anti-surge, Lightningproof, Over-current protection) Wireless specification: 1. Frequency Band: 2.412 ~ 2.484 GHz 2. Wireless network: Station / AP / AP+Station Mode 3. Security mechanism: WPA-PSK / WPA2-PSK 4. Encryption type: TKIP / AES 5. Transmitting power: - 802.11b: +19dBm (11Mbps) - 802.11g: +18dBm (54Mbps) - 802.11n: +17dBm (HT20, MCS7); +17dBm (HT40, MCS7) 6. Receiving sensitivity: - 802.11b: -89dBm (11Mbps) - 802.11g: -81dBm (54Mbps) - 802.11n: -73dBm (HT20, MCS7); -71dBm (HT40, MCS7) Serial specification: 1. Baudrate: 300 ~ 460800 bps 2. Parity bit: None, odd, even, mark, space 3. Data bit: 5 ~ 9 bits 4. Flow control: N/A Software 1.Protocol: TCP / UDP / ARP / ICMP / DHCP / DNS / HTTP / MQTT 2. Configuration: Host, web browser, serial AT command 3. Communication method: TCP/IP direct communication, VCOM 4. Operating mode: Transparent transmission, serial command, HTTPD Client, Modbus TCP to Modbus RTU Environmental requirements 1. Working temperature: -40 ~ 85 degree C 2. Storage temperature: -45 ~ 125 degree C 3. Humidity range: 5% ~ 95% relative humidityPackage List1. RS485 TO WIFI/ETH x 1 2. Antenna x 1Specification: Package Weight One Package Weight 0.17kgs / 0.37lb One Package Size 15cm * 8cm * 5cm / 5.91inch * 3.15inch * 1.97inch Qty per Carton 100 Carton Weight 17.00kgs / 37.48lb Carton Size 42cm * 50cm * 32cm / 16.54inch * 19.69inch * 12.6inch Loading Container 20GP: 396 cartons * 100 pcs = 39600 pcs40HQ: 921 cartons * 100 pcs = 92100 pcs

Lis Plus Moins

GSM/GPRS/GNSS/Bluetooth HAT for Raspberry Pi, Based on SIM868Overview1. This is a handy, low power Raspberry Pi HAT which features multi communication functionalities: GSM, GPRS, GNSS and Bluetooth.2. It allows your Pi to easily make a telephone call, send messages, connect to wireless Internet, global position, transfer data via Bluetooth, and so on.Features1. Raspberry Pi connectivity, compatible with Raspberry Pi 2B/3B/3B+/Zero/Zero W2. Support SMS, phone call, GPRS, DTMF, HTTP, FTP, MMS, email, etc.3. Support GPS, COMPASS, Glonass, LBS base station positioning, omni-positioning4. Bluetooth 3.0, supports data transferring through Bluetooth5. Onboard USB TO UART converter CP2102 for UART debugging6. 6x LEDs for indicating the module working status7. SIM card slot for 1.8V/3V SIM card8. RTC with backup battery holder9. Baudrate auto detection (1200bps ~115200bps)10. Control via AT commands (3GPP TS 27.007, 27.005, and SIMCOM enhanced AT Commands)11. Support SIM application toolkit: GSM 11.14 Release 9912. Come with development resources and manual (examples for Raspberry Pi/Arduino/STM32)GSM/GPRS1. Band- GSM 850/EGSM 900/DCS 1800/PCS 1900 MHz- Quad-band auto search- Compliant to GSM phase 2/2+2. Emitting power- Class 4 (2W @ GSM 850/EGSM 900 MHz)- Class 1 (1W @ DCS 1800/PCS 1900 MHz)4. GPRS connectivity- GPRS multi-slot class 12 (default)- GPRS multi-slot class 1~12 (configurable)5. GPRS data feature- Downlink speed: max 85.6kbps- Uplink speed: max 85.6kbps- Coding schemes: CS-1\CS-2\CS-3\CS-4- Support PAP (Password Authentication Protocol) for PPP connection- Support PBCCH- Support USSD6. SMS- Support: MT/MO/CB/Text/PDU mode- SMS storage: SIM card7. Audio- Voice encode/decode mode: Half Rate\Full Rate\Enhanced Full Rate\Adaptive muti rate- Support echo cancellation- Support noise reductionGNSS1. Receiver type- 33 tracking channels- 99 acquisition channels- GPS L1 C/A code2. Sensitivity- Tracking: -165 dBm- Cold starts: -148 dBm3. Time-To-First-Fix- Cold starts: 28s (typ.)- Hot starts: < 1s- Warm starts: 26s4. Accuracy- Horizontal position: <2.5m CEPBluetooth1. Integrates AT commands2. Compliant to Bluetooth specification3.0 + EDR3. Support SPP, OPP, HFP/HSP, etc.Misc1. Operating voltage: 5V2. Operating temperature: -40 degree C ~ 85 degree C3. Storage temperature: -45 degree C ~ 90 degree C4. Dimensions: 30.2mm x 65mmWhat is on Board1. SIM868 module2. ZMM5V1: Regulator diode3. SMF05C: TVS diode4. CP2102: USB TO UART converter5. MP1482: Power chip6. NDC7002N: Voltage level translator7. GPS status indicator8. NET indicator:- Flashes fast when the module starts up- Flashes slowly after GSM register succeed9. STA module working status indicator10. SIM868 UART Tx/Rx indicator11. Power indicator12. SIM868 control button: press the button and hold for 1s, to startup/shutdown the SIM86813 .Raspberry Pi GPIO connector14. SIM card slot15. USB TO UART interface16. 3.5mm earphone/mic jack17. GNSS antenna connector18. Bluetooth antenna connector19. GSM antenna connector20. CR1220 battery holder: for RTC backup battery21. UART selection switch- A: Control the SIM868 through USB TO UART- B: Control the SIM868 through Raspberry Pi- C: Access Raspberry Pi through USB TO UARTPackage Contents1. GSM/GPRS/GNSS HAT x12. GSM Antenna x13. GPS External Antenna (B) x14. Bluetooth Antenna x15. USB type A plug to micro plug cable x16. RPi screws pack (2pcs) x1Specification: Package Weight One Package Weight 0.19kgs / 0.41lb One Package Size 14cm * 8cm * 3cm / 5.51inch * 3.15inch * 1.18inch Qty per Carton 260 Carton Weight 15.00kgs / 33.07lb Carton Size 56cm * 40cm * 39cm / 22.05inch * 15.75inch * 15.35inch Loading Container 20GP: 305 cartons * 260 pcs = 79300 pcs40HQ: 708 cartons * 260 pcs = 184080 pcs

Lis Plus Moins

FeaturesThe Solar Power Manager (B) is compatible with general 6V~24V solar panels. It can recharge the 3.7V rechargeable Li-po battery through solar panel or USB TYPE-C connection, and provides 5V / 3A regulated output (with multi protocols support including PD/QC/FCP/PE/SFCP). The module features MPPT (Maximum Power Point Tracking) function and multi protection circuits, therefore, it is able to keep operating with high-efficiency, stability, and safety. It is suitable for solar powered, low-power IoT, and other environmental protection projects. 1. Support MPPT (Maximum Power Point Tracking) function, maximizing the efficiency of the solar panel 2. Flexible battery recharging: from solar panel or USB TYPE-C power adapter 3. Compatible with 6V~24V solar panels, DC-002 jack input or screw terminal input 4. Onboard MPPT SET switch, select the level closed to input level to improve recharging efficiency 5. Onboard aluminum electrolytic capacitor and SMD ceramic capacitor, reducing the ripple, stable performance 6. PH2.0 battery connector, with embedded 10000mAh 3.7V rechargeable Li-po battery 7. Several LED indicators, for monitoring the status of solar panel and battery 8. Multi protection circuits: over charge / over discharge / reverse-proof / over heat / over current, stable and safe to useSpecification: Package Weight One Package Weight 0.35kgs / 0.77lb One Package Size 20cm * 15cm * 5cm / 7.87inch * 5.91inch * 1.97inch Qty per Carton 40 Carton Weight 13.00kgs / 28.66lb Carton Size 42cm * 32cm * 27cm / 16.54inch * 12.6inch * 10.63inch Loading Container 20GP: 734 cartons * 40 pcs = 29360 pcs40HQ: 1705 cartons * 40 pcs = 68200 pcs

Lis Plus Moins