Afficher les produits précédents
1. This product uses the active laser scanning and passive scanning method of combining wireless, can accurately identify: Eavesdropping devices, tracking devices, car eavesdropping, wireless pinhole camera, wired camera, electrical sources, and so on. Can effectively prevent eavesdropping videotaping, fraud and protect personal privacy data and information confidential 2. With automatic detection, the host to carry, at risk when there is eavesdropping devices, pinhole cameras, casino ye lie. Host will prompt your body automatically detects the danger. 3. Has a signal strength indicator, to quickly find the source of the signal 4. The sensitivity adjustment potent milometer can be adjusted (increased sensitivity to widen the detection range or lower sensitivity to shorten the detection range) radio power at faster to find. 5. Detection modes: A laser probe, vibration (silent), beep detection probe detection, LED display, Headphone mute detection 6. low-voltage prompts, built-in rechargeable battery 7. Laser detection: Host window can be seen through the eyes of all inside of the current situation facing the camera lens 8. Wireless Sweep: Frequency detection range (1MHZ-6500MHZ) Specification: 1. Material: ABS 2. Screen Size: 1.6 inch 3. Charging Voltage: DC 5V / 500mA 4. Power: 500mW~200mW (detection distance: 30~50cm) 5. Power: 300mW~600mW (detection distance: 100~200cm) 6. Power: 800mW~1200mW (detection distance: 300~1000cm) 9. Detection Laser Wave Length: 920nm 10. Detection Frequency Range: 1MHz~6.500MHz 11. Working Range: 1~10m 12. Size: 102 x 58 x 23mmSpecification: Package Weight One Package Weight 0.21kgs / 0.46lb One Package Size 14.2cm * 9.2cm * 4.9cm / 5.59inch * 3.62inch * 1.93inch Qty per Carton 80 Carton Weight 15.80kgs / 34.83lb Carton Size 50cm * 38cm * 30cm / 19.69inch * 14.96inch * 11.81inch Loading Container 20GP: 467 cartons * 80 pcs = 37360 pcs40HQ: 1086 cartons * 80 pcs = 86880 pcs
£16.99
1) Simple, vivid and no-wire installation design avoid troubles and save money when in installation and do not effect decorate environment 2) Remote control range up to 80 meters in open air, suitable for homes and high floor houses 3) 38 Melodies for selection 4) Easy to install 5) Two receivers included 6) For receiver: Powered by 2 x AA batteries (not included) 7) For remote control: Powered by 1 * 23A battery (Included) 8) Comes with mounting screws and stickerSpecification: Package Weight One Package Weight 0.25kgs / 0.55lb One Package Size 21cm * 17cm * 3cm / 8.27inch * 6.69inch * 1.18inch Qty per Carton 20 Carton Weight 6.20kgs / 13.67lb Carton Size 37cm * 23cm * 33cm / 14.57inch * 9.06inch * 12.99inch Loading Container 20GP: 949 cartons * 20 pcs = 18980 pcs40HQ: 2204 cartons * 20 pcs = 44080 pcs
£5.99
1) Input: AC100 - 240V 1.0A 50-60Hz 2) Output: 12V 2A 3) Output power: 24WSpecification: Package Weight One Package Weight 0.37kgs / 0.81lb One Package Size 10cm * 6cm * 4cm / 3.94inch * 2.36inch * 1.57inch Qty per Carton 30 Carton Weight 10.00kgs / 22.05lb Carton Size 45cm * 40cm * 30cm / 17.72inch * 15.75inch * 11.81inch Loading Container 20GP: 493 cartons * 30 pcs = 14790 pcs40HQ: 1146 cartons * 30 pcs = 34380 pcs
£4.99
1) Model: HDL 1203A 2) Input: AC100 - 240V 1.0A 50-60Hz 3) Output: DC 12V 3A 4) Output power: 36W 5) Cable Length: 1.2mSpecification: Package Weight One Package Weight 0.40kgs / 0.88lb One Package Size 20cm * 15cm * 5cm / 7.87inch * 5.91inch * 1.97inch Qty per Carton 24 Carton Weight 9.50kgs / 20.94lb Carton Size 45cm * 40cm * 30cm / 17.72inch * 15.75inch * 11.81inch Loading Container 20GP: 493 cartons * 24 pcs = 11832 pcs40HQ: 1146 cartons * 24 pcs = 27504 pcs
£3.99 - £4.99
About the product1. This product bound the video signal of the camera and the control signal of RS485 reverse controller in one coaxial cable transmission. It use frequency division multiplexing technique, which means the control signal and video signal in different frequency modulation, and composite together transmission. It can transmit four channel homonymous or reverse transmission video signal and RS485 control signal in one cable. It can transmit 600 meters by using common video cable, which can enhance the utilization rate of cable, also it has many characteristics, such as a clear image, easy for installation and so on. 2. It has solved control signal transmission over a long distance, greatly extended video signal transmission distance. The transmission way save material and cost, construction is convenient, without debugging, stable, reliable, etc. System extension and transformation is more flexibility. It is an ideal equipment of control signal transmissionAttentions1. L<=500m; 1<=500m; (1 +L)<=500m. 2. Before using this equipment, please carefully read the description of the device. 3. Installation in strict accordance with regulations. 4. Note that the equipment is waterproof, moisture-proof, and handle with care. 5. Please use stable power supply voltage DC12V. 6. Please install the appropriate height to avoid damage, electric shock. 7. Before plug-in power, please according to the panel chart shown below, connect the cable; 8. Check whether the connection cable firm, in case contact undesirable. 9. Equipment failure, do not open without authorization, please contact the after-sale service department.Illustration1. Line in connected receiver 2. DC12V power supply 3. Power supply indicator lamp 4. Video in connected camera 5. Line in connection transmitter 6. Video out connected monitor or DVR.Specification: Package Weight One Package Weight 0.96kgs / 2.13lb One Package Size 33cm * 18.5cm * 5.5cm / 12.99inch * 7.28inch * 2.17inch Qty per Carton 20 Carton Weight 14.80kgs / 32.63lb Carton Size 57cm * 39cm * 35cm / 22.44inch * 15.35inch * 13.78inch Loading Container 20GP: 342 cartons * 20 pcs = 6840 pcs40HQ: 795 cartons * 20 pcs = 15900 pcs
£60.99
1. Made of good quality metal material, durable to use 2. Great for short distance connection 3. Simple and professional appearance for cabling 4. UHF female to UHF female connector. 5. This adapter is used to connect to different types of cable assembles, antennas and access points.Specification: General Material Metal Connector Types UHF Female Size 26*15*15mm Weight 17g Package Weight One Package Weight 0.03kgs / 0.06lb One Package Size 12cm * 8cm * 1.5cm / 4.72inch * 3.15inch * 0.59inch Qty per Carton 200 Carton Weight 4.80kgs / 10.58lb Carton Size 26cm * 18cm * 17cm / 10.24inch * 7.09inch * 6.69inch Loading Container 20GP: 3351 cartons * 200 pcs = 670200 pcs40HQ: 7780 cartons * 200 pcs = 1556000 pcs
£2.99 £0.99
1. Made of good quality metal material, durable to use 2. Great for short distance connection 3. Simple and professional appearance for cabling 4. Easy for installation save time and money 5. Size: 28 x 14mm 6. Weight: 17gSpecification: Package Weight One Package Weight 0.01kgs / 0.02lb Qty per Carton 300 Carton Weight 6.10kgs / 13.45lb Carton Size 20cm * 11cm * 11cm / 7.87inch * 4.33inch * 4.33inch Loading Container 20GP: 11019 cartons * 300 pcs = 3305700 pcs40HQ: 25580 cartons * 300 pcs = 7674000 pcs
£2.99 £0.99
Specifications: 1. Male/Female BNC Connector 2. 75OHM and 50OHM are available 3. BNC Crimp on 4. All brass plug,Gold pin 5. For connecting RG6 Coaxial cable Features: 1. Bayonet coupling, small size and low cost. 2. 50ohm and 75ohm are available and intermateable 3. Various options for different applications 4. Applications: Antennas, broadcast, radios, telecomSpecification: Package Weight One Package Weight 0.01kgs / 0.02lb Qty per Carton 64 Carton Weight 5.50kgs / 12.13lb Carton Size 30cm * 20cm * 20cm / 11.81inch * 7.87inch * 7.87inch Loading Container 20GP: 2222 cartons * 64 pcs = 142208 pcs40HQ: 5158 cartons * 64 pcs = 330112 pcs
£2.99 £0.99
1. Straight female bnc connector with spring for CCTV 2. Temperature range:- 40 to 155 degree C 3. Insulation resistance:5000 Ohm (min) 4. Character impedance: 50/75 ohm 5. Frequency range: 0-3GHZ 6. Voltage rating: 500V(r ms) 7. Disengage force:0.6N (Min) 8. Center conductor: (Max)1.5mohm 9. Outer conductor : (Max) 1mohm 10. Durability : 500 cycles 11. Intermediate pressurization:1500V, 0.5mA AC/minSpecification: Package Weight One Package Weight 0.06kgs / 0.13lb Qty per Carton 100 Carton Weight 5.30kgs / 11.68lb Carton Size 30cm * 18cm * 18cm / 11.81inch * 7.09inch * 7.09inch Loading Container 20GP: 2743 cartons * 100 pcs = 274300 pcs40HQ: 6368 cartons * 100 pcs = 636800 pcs
£2.99 £1.99
1. Made of good quality metal material, durable to use 2. Great for short distance connection 3. Simple and professional appearance for cabling 4. Easy for installation save time and money 5. All brass plug, gold pin 6. Various options for different applications 7. Applications: Antennas, broadcast, radios, telecomSpecification: Package Weight One Package Weight 0.02kgs / 0.04lb One Package Size 5cm * 4cm * 4cm / 1.97inch * 1.57inch * 1.57inch Qty per Carton 500 Carton Weight 4.00kgs / 8.82lb Carton Size 15cm * 15cm * 12cm / 5.91inch * 5.91inch * 4.72inch Loading Container 20GP: 9876 cartons * 500 pcs = 4938000 pcs40HQ: 22927 cartons * 500 pcs = 11463500 pcs
£2.99 £0.99
1. Made of good quality metal material, durable to use 2. Great for short distance connection 3. Simple and professional appearance for cabling 4. Easy for installation save time and money 5. Various options for different applications 6. Applications: Antennas, broadcast, radios, telecomSpecification: Package Weight One Package Weight 0.01kgs / 0.02lb Qty per Carton 250 Carton Weight 6.90kgs / 15.21lb Carton Size 16cm * 15cm * 13cm / 6.3inch * 5.91inch * 5.12inch Loading Container 20GP: 8547 cartons * 250 pcs = 2136750 pcs40HQ: 19841 cartons * 250 pcs = 4960250 pcs
£2.99 £1.99
1. Made of good quality metal material, durable to use 2. Great for short distance connection 3. Simple and professional appearance for cabling 4. Easy for installation save time and money 5. Various options for different applications 6. Applications: Antennas, broadcast, radios, telecomSpecification: Package Weight One Package Weight 0.01kgs / 0.02lb Qty per Carton 500 Carton Weight 6.20kgs / 13.67lb Carton Size 18cm * 15cm * 11cm / 7.09inch * 5.91inch * 4.33inch Loading Container 20GP: 8978 cartons * 500 pcs = 4489000 pcs40HQ: 20843 cartons * 500 pcs = 10421500 pcs
£2.99 £0.99
1. Made of good quality metal material, durable to use 2. Each item has been tested before shipment 3. Simple and professional appearance for cabling 4. 93 ohm BNC plug terminator 5. Size: 2.9cm x 1.3cm 6. Weight: 9gSpecification: Package Weight One Package Weight 0.03kgs / 0.07lb One Package Size 4cm * 1.5cm * 1.5cm / 1.57inch * 0.59inch * 0.59inch Qty per Carton 500 Carton Weight 10.70kgs / 23.59lb Carton Size 30cm * 18cm * 15cm / 11.81inch * 7.09inch * 5.91inch Loading Container 20GP: 3292 cartons * 500 pcs = 1646000 pcs40HQ: 7642 cartons * 500 pcs = 3821000 pcs
£2.99 £0.99
1) Compatible with 2.4GHz 802.11b and 802.11g Wireless Standards 2) Advanced Panel Designed for Excellent Wireless Range and Performance 3) Plug and Play Installation 4) Works with most Wireless Devices with removable external antennas * Specifications 1) Frequency Range(MHz):800~960/1710~2500 2) Polarization: Vertical or Horizontal 3) Gain: 8 dBi 4) Connector: N female 5) Cable length: Approx 15cmSpecification: Package Weight One Package Weight 0.63kgs / 1.38lb One Package Size 45cm * 22cm * 6.5cm / 17.72inch * 8.66inch * 2.56inch Qty per Carton 8 Carton Weight 5.00kgs / 11.02lb Carton Size 50cm * 40cm * 30cm / 19.69inch * 15.75inch * 11.81inch Loading Container 20GP: 444 cartons * 8 pcs = 3552 pcs40HQ: 1031 cartons * 8 pcs = 8248 pcs
£5.99
1) Plug and Play Installation. 2) Compatible with 2.4GHz 802.11b/g/n Wireless Standards. 3) Gold core Connectors for Increased Wireless Performance. 3) Works with most Wireless Devices. 4) Impedance: 50 ohm 5) Connectors: N male to N male 6) Cable Length: 15mSpecification: Package Weight One Package Weight 0.80kgs / 1.76lb One Package Size 30cm * 30cm * 4cm / 11.81inch * 11.81inch * 1.57inch Qty per Carton 10 Carton Weight 9.40kgs / 20.72lb Carton Size 40cm * 30cm * 30cm / 15.75inch * 11.81inch * 11.81inch Loading Container 20GP: 740 cartons * 10 pcs = 7400 pcs40HQ: 1719 cartons * 10 pcs = 17190 pcs
£6.99 - £14.99
* Application place of mobile phone signal amplifier: 1) Small regions signal blind or weak signal area, such as underground or semi-underground place of business, basements, underground parking, etc. 2) Small-scale hot-spot signal Complaints areas, such as conference rooms, a small supermarket, small shopping malls, the office and small public areas, etc. 3) Traffic and large social influence areas, such as bars, cafes, dance halls, cafes, fitness clubs,leisure and entertainment, etc. 4) Home, office, luxury yachts, private cars, public security system and road safety management, etc. * Specifications: 1) Up-link frequency: 890-915MHz 2) Down-link frequency: 935-960MHz 3) Up-link Gain: 70 dB 4) Down-link Gain: 75 dB 5) Gain adjustable range: MGCa?￥30dB 6) Output power(dBm): a?￥20 7) Pass band ripple: GSM 4dB 8) Guard band rejection: GSM (BW-60dB)a?¤42 MHz (BW-70dB)a?¤45 MHz 9) I/O impedance: 50/N Connector 10) I/O return loss: a?¤-10dB 11) Noise figure: a?¤-8dB 12) Intermodulation attenuation (Po=13 dBm): a?￥40dBc 13) Transmission delay: a?¤0.5us 14) Ambient temperature: -10 Degree C ???50 Degree C 15) Power supply: AC110???220V?±10% 45???55Hz 16) Size: 200mm*140mm*40mm 17) Product weight: 1.06kg 18) Coverage: approx. 50 square meters indoors. 19) Antenna: 50x8x2.2cm * Characteristic: 1) Fully integrated 900 MHz antenna system 2) Powerful amplifier enables up to + 85 dB of signal gain including cable loss 3) Intelligent signal processing and real time adaptive operation 4) Automatically adjusts power levels as needed to ensure a consistent coverage footprint 5) Reprogrammable (in the field) enabling spectrum or carrier reconfigurations as needed 6) Auto-Trac LED diagnostics displays aid install and operation 7) Patented algorithms and adaptive processing ensure our products will not interfere with other wireless frequencies or radio devices * The package contains: 1) 70dB GSM Cellular Phone Signal Amplifier 2) 8 dB outdoor antenna 3) 2.5 dB indoor antenna 4) 10m cable 5) Mounting accessories: AC power supply, user manualSpecification: Package Weight One Package Weight 3.70kgs / 8.16lb One Package Size 41cm * 31cm * 19cm / 16.14inch * 12.2inch * 7.48inch Qty per Carton 2 Carton Weight 7.40kgs / 16.31lb Carton Size 53cm * 38cm * 22cm / 20.87inch * 14.96inch * 8.66inch Loading Container 20GP: 601 cartons * 2 pcs = 1202 pcs40HQ: 1397 cartons * 2 pcs = 2794 pcs
£59.99
About The ProductThis LCD micro-repeater kit includes an outdoor and indoor antenna, suitable for mobile phone signal boosting, presenting good amplification effect with no blind spot, which is widely used at home, office, meeting room and other small places. Note: Please ensure your phone frequency the same with our repeater before purchase, for different phone may use different frequency.Features1. Mini GSM 900MHz LCD repeater for mobile phone signal boosting. 2. With LCD indicator to show real-time work state. 3. ALC function, no interference to work station. 4. Low noise, low heat, low power consumption. 5. Alloy material, durable in performance. 6. Perfect design, easy installation. 7. Antenna gain: 5dB outdoor antenna, 3dB indoor antenna. 8. Outdoor antenna length: 10m/32.81ft.Specification: General Model GSM900MHz Material Aluminum Alloy Frequency Range Uplink 890-915MHz, Downlink 935-960MHz Gain Uplink 45-55dB, Downlink 50-70dB Input Power -70~-40dBm/FA (1.23MHz) Output Power Uplink 17dBm+/-3dBm, Downlink 17dBm+/-3dBm Power Supply DC5V/2A (AC110-240V) Impedance 50ohm RF Connector N-Female Outdoor Antenna Length 10m Dimensions & Weight Size 14.2*10*2cm Package Include Package Contents 1 x 5dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x AC Power Supply 1 x Manual 1 x Signal Booster Package Weight One Package Weight 0.74kgs / 1.63lb One Package Size 30cm * 20cm * 5cm / 11.81inch * 7.87inch * 1.97inch Qty per Carton 10 Carton Weight 8.80kgs / 19.40lb Carton Size 52cm * 42cm * 32cm / 20.47inch * 16.54inch * 12.6inch Loading Container 20GP: 381 cartons * 10 pcs = 3810 pcs40HQ: 885 cartons * 10 pcs = 8850 pcs
£22.99
Features: 1. High-gain linear power amplifier 2. ALC and AGC function technology 3. Ultra-low noise receive amplifier 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters 5. Stable and reliable electromagnetic compatibility design 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications 7. With full-duplex communication mode 8. Dispel the heat effective reasonable, the structure is pretty, the volume is suitable Install Repeater: 1. Step 1: Use your mobile phone to test signal strength outside house or on roof, -70dbm is the basic requirement (full bar) 2. Step 2: Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal 3. Step 3: Run outdoor coaxial cable into building in a convenient location to connect with signal repeater 4. Step 4: Mount your indoor antenna with signal repeater 5. Step 5: Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal 6. Note: Connect outdoor (BTS) port with outdoor antenna, connect indoor ANT(MS) port with indoor antenna, outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away from each other at least 7. Indoor and outdoor antenna must be separated by wall Working: 1. The outside antenna catches the low signal from the mobile base station and delivers it to the cell phone amplifier through the connection cable (coax) 2. After the signal is accepted by the phone amplifier, the device amplifies it 3. Then this amplified signal goes through the connection cable (coax) to the inside antenna 4. And after that, the amplified signal transmits to the cell phone Technique Supporting: 1. If still weak signal receipt after installation, please check if outdoor antenna point to signal tower correctly or elsewhere has stronger signal and confirm signal strength achieve-70DBM. 2. If still have no signal after installation, please check our device power adapter whether connected perfectly? And connectors connect well. 3. If strength is not steady, please check if outdoor and indoor antenna is too close; please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 4. Packed the outdoor connector by waterproof glue, otherwise wet reduce the signal cover areaSpecification: General Frequency Range GSM 900MHz, Uplink 890-915MHz, Downlink 935-960MHz Gain Uplink 58-62dB, Downlink 58-62dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC: 100~240V, 50/ 60Hz; DC: 5V 1A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 140m x 98mm x 20mm Weight 280g Package Include Package Contents 1 x 12dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 5m RG6-50 OHM Indoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual 1 x Signal Booster Package Weight One Package Weight 1.18kgs / 2.59lb One Package Size 50cm * 20cm * 8cm / 19.69inch * 7.87inch * 3.15inch Qty per Carton 10 Carton Weight 13.50kgs / 29.76lb Carton Size 52cm * 42cm * 42cm / 20.47inch * 16.54inch * 16.54inch Loading Container 20GP: 290 cartons * 10 pcs = 2900 pcs40HQ: 674 cartons * 10 pcs = 6740 pcs
£22.99
Features1. High-gain linear power amplifier 2. ALC and AGC function technology 3. Ultra-low noise receive amplifier 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters 5. Stable and reliable electromagnetic compatibility design 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications 7. With full-duplex communication mode 8. Dispel the heat effective reasonable, the structure is pretty, the volume is suitableInstall Repeater1. Step 1: Use your mobile phone to test signal strength outside house or on roof, -70dbm is the basic requirement (full bar) 2. Step 2 Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal 3. Step3: Run outdoor coaxial cable into building in a convenient location to connect with signal repeater 4. Step 4: Mount your indoor antenna with signal repeater 5. Step 5: Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal 6. Note: Connect outdoor (BTS) port with outdoor antenna, connect indoor ANT(MS) port with indoor antenna, outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away from each other at least 7. Indoor and outdoor antenna must be separated by wallWorking1. The outside antenna catches the low signal from the mobile base station and delivers it to the cell phone amplifier through the connection cable (coax) 2. After the signal is accepted by the phone amplifier, the device amplifies it 3. Then this amplified signal goes through the connection cable (coax) to the inside antenna 4. And after that, the amplified signal transmits to the cell phoneTechnique Supporting1. If still weak signal receipt after installation, please check if outdoor antenna point to signal tower correctly or elsewhere has stronger signal and confirm signal strength achieve-70DBM. 2. If still have no signal after installation, please check our device power adapter whether connected perfectly? And connectors connect well. 3. If strength is not steady, please check if outdoor and indoor antenna is too close; please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 4. Packed the outdoor connector by waterproof glue, otherwise wet reduce the signal cover areaSpecification: General Frequency Range CDMA 850MHz, Uplink 824-849MHz, Downlink 869-894MHz Gain Uplink 58-62dB, Downlink 58-62dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC: 100~240V, 50/ 60Hz; DC: 5V 1A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 140mm x 98mm x 20mm Weight 280g Package Include Package Contents 1 x 12dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual 1 x Signal Booster Package Weight One Package Weight 0.76kgs / 1.67lb One Package Size 30cm * 12cm * 10cm / 11.81inch * 4.72inch * 3.94inch Qty per Carton 10 Carton Weight 9.80kgs / 21.61lb Carton Size 52cm * 50cm * 32cm / 20.47inch * 19.69inch * 12.6inch Loading Container 20GP: 320 cartons * 10 pcs = 3200 pcs40HQ: 744 cartons * 10 pcs = 7440 pcs
£24.99
Features1. High-gain linear power amplifier 2. ALC and AGC function technology 3. Ultra-low noise receive amplifier 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters 5. Stable and reliable electromagnetic compatibility design 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications 7. With full-duplex communication mode 8. Dispel the heat effective reasonable, the structure is pretty, the volume is suitableInstall Repeater1. Step 1: Use your mobile phone to test signal strength outside house or on roof, -70dbm is the basic requirement (full bar) 2. Step 2 Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal 3. Step3: Run outdoor coaxial cable into building in a convenient location to connect with signal repeater 4. Step 4: Mount your indoor antenna with signal repeater 5. Step 5: Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal 6. Note: Connect outdoor (BTS) port with outdoor antenna, connect indoor ANT(MS) port with indoor antenna, outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away from each other at least 7. Indoor and outdoor antenna must be separated by wallWorking1. The outside antenna catches the low signal from the mobile base station and delivers it to the cell phone amplifier through the connection cable (coax) 2. After the signal is accepted by the phone amplifier, the device amplifies it 3. Then this amplified signal goes through the connection cable (coax) to the inside antenna 4. And after that, the amplified signal transmits to the cell phoneTechnique Supporting1. If still weak signal receipt after installation, please check if outdoor antenna point to signal tower correctly or elsewhere has stronger signal and confirm signal strength achieve-70DBM. 2. If still have no signal after installation, please check our device power adapter whether connected perfectly? And connectors connect well. 3. If strength is not steady, please check if outdoor and indoor antenna is too close; please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 4. Packed the outdoor connector by waterproof glue, otherwise wet reduce the signal cover areaSpecification: General Frequency Range CDMA 850MHz, Uplink 824-849MHz, Downlink 869-894MHz Gain Uplink 58-62dB, Downlink 58-62dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC: 100~240V, 50/ 60Hz; DC: 5V 1A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 140mm x 98mm x 20mm Weight 280g Package Include Package Contents 1 x 12dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 5m RG6-50 OHM Indoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual 1 x Signal Booster Package Weight One Package Weight 1.39kgs / 3.07lb One Package Size 51cm * 25cm * 10cm / 20.08inch * 9.84inch * 3.94inch Qty per Carton 6 Carton Weight 10.00kgs / 22.05lb Carton Size 52cm * 52cm * 32cm / 20.47inch * 20.47inch * 12.6inch Loading Container 20GP: 308 cartons * 6 pcs = 1848 pcs40HQ: 715 cartons * 6 pcs = 4290 pcs
£24.99
Why to use1. Cell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save life of somebody. 2. Unfortunately, there are still some places where one can find themselves out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: 1) Parking lots, tunnels 2) Big stores, office buildings 3) Cars, boats etc. 4) House in remote areas etcFeatures1. High-gain linear power amplifier 2. ALC and AGC function technology 3. Ultra-low noise receive amplifier 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications 7. With full-duplex communication mode. 8. Dispel the heat effective reasonable, the structure is pretty, the volume is suitableHow to work1. The outside antenna catches the low signal from the mobile base station and delivers it to the cell phone amplifier through the connection cable (coax). 2. After the signal is accepted by the phone amplifier, the device amplifies it. 3. Then this amplified signal goes through the connection cable (coax) to the inside antenna. 4. And after that, the amplified signal transmits to the cell phoneHow to install1. Step 1: Use your mobile phone to test signal strength outside house or on roof, -70dbm is the basic requirement (full bar). 2. Step 2: Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Step 3: Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Step 4: Mount your indoor antenna with signal repeater 5. Step 5: Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signalNotes1. Connect outdoor (BTS) port with outdoor antenna, connect indoor ANT(MS) port with indoor antenna, outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away from each other at least. 2. Indoor and outdoor antenna must be separated by wallTechnique supports1. If still weak signal receipt after installation, please check if outdoor antenna point to signal tower correctly or elsewhere has stronger signal and confirm signal strength achieve-70DBM. 2. If still have no signal after installation, please check our device power adapter whether connected perfectly? And connectors connect well. 3. If strength is not steady, please check if outdoor and indoor antenna is too close; please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 4. Packed the outdoor connector by waterproof glue, otherwise wet reduce the signal cover areaSpecification: General Frequency Range WCDMA 2100MHz, Uplink 1920-1980MHz, Downlink 2110-2170MHz Gain Uplink 53-57dB, Downlink 58-62dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC: 100~240V, 50/ 60Hz; DC: 5V 2A Power Consumption <5W RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 100mm x 45mm x 18mm Weight 350g Package Include Package Contents 1 x 12dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 5m RG6-50 OHM Indoor Coaxial Cable 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 1.00kgs / 2.20lb One Package Size 51cm * 18cm * 13cm / 20.08inch * 7.09inch * 5.12inch Qty per Carton 4 Carton Weight 5.20kgs / 11.46lb Carton Size 53cm * 38cm * 28cm / 20.87inch * 14.96inch * 11.02inch Loading Container 20GP: 472 cartons * 4 pcs = 1888 pcs40HQ: 1097 cartons * 4 pcs = 4388 pcs
£31.99
About Signal BoosterCell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save a life. Unfortunately, there are still some places where one can find themselves - out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: parking lots, tunnels, big stores, office buildings, cars, boats, house in remote areas, etc. Here we will bring you a new kind of LED signal booster. Welcome to buy!Features1. High-gain linear power amplifier. 2. ALC and AGC function technology. 3. Ultra-low noise receive amplifier. 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters. 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications. 7. With full-duplex communication mode. 8. It explores an effective and reasonable method to dispel the heat.Installation Steps1. Use your mobile phone to test signal strength outside house or on roof, -70dBm is the basic requirement (full bar). 2. Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Mount your indoor antenna with signal repeater. 5. Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Notices1. Connect outdoor (BTS) port with outdoor antenna. Connect indoor ANT (MS) port with indoor antenna. Outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away at least from each other. 2. Indoor and outdoor antennas must be separated by wall. 3. If the signal is still weak after installation, please check whether or not the outdoor antenna is pointed to signal tower correctly or elsewhere with stronger signal and confirm that the signal strength achieved -70dBm. 4. If no signal for a long time after installation, please check the device power adapter whether or not connected perfectly and connectors connect well. 5. If strength is not steady, please check if outdoor and indoor antennas are too close. Please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 6. Packed the outdoor connector by waterproof glue, otherwise wet condition will reduce the signal cover area.Specification: General Frequency Range GSM 900MHz, Uplink 890-915MHz, Downlink 935-960MHz Gain Uplink 63-67dB, Downlink 63-67dB Output Power Uplink 15-19dBm, Downlink 15-19dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC:100~240V, 50/60Hz; DC:12V 2A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 198 x 186 x 20mm Weight 1200g Package Include Package Contents 1 x 5dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 1.39kgs / 3.07lb One Package Size 31cm * 20cm * 11cm / 12.2inch * 7.87inch * 4.33inch Qty per Carton 4 Carton Weight 7.40kgs / 16.31lb Carton Size 42cm * 33cm * 24cm / 16.54inch * 12.99inch * 9.45inch Loading Container 20GP: 801 cartons * 4 pcs = 3204 pcs40HQ: 1861 cartons * 4 pcs = 7444 pcs
£32.99
About Signal BoosterCell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save a life. Unfortunately, there are still some places where one can find themselves - out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: parking lots, tunnels, big stores, office buildings, cars, boats, house in remote areas, etc. Here we will bring you a new kind of LED 3G signal booster. Welcome to buy!Features1. High-gain linear power amplifier. 2. ALC and AGC function technology. 3. Ultra-low noise receive amplifier. 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters. 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications. 7. With full-duplex communication mode. 8. It explores an effective and reasonable method to dispel the heat.Installation Steps1. Use your mobile phone to test signal strength outside house or on roof, -70dBm is the basic requirement (full bar). 2. Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Mount your indoor antenna with signal repeater. 5. Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Notices1. Connect outdoor (BTS) port with outdoor antenna. Connect indoor ANT (MS) port with indoor antenna. Outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away at least from each other. 2. Indoor and outdoor antennas must be separated by wall. 3. If the signal is still weak after installation, please check whether or not the outdoor antenna is pointed to signal tower correctly or elsewhere with stronger signal and confirm that the signal strength achieved -70dBm. 4. If no signal for a long time after installation, please check the device power adapter whether or not connected perfectly and connectors connect well. 5. If strength is not steady, please check if outdoor and indoor antennas are too close. Please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 6. Packed the outdoor connector by waterproof glue, otherwise wet condition will reduce the signal cover area.Specification: General Frequency Range WCDMA 2100MHz, Uplink 1920-1980MHz, Downlink 2110-2170MHz Gain Uplink 63-67dB, Downlink 63-67dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC:100~240V, 50/60Hz; DC:12V 2A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 198 x 182 x 20mm Weight 1200g Package Include Package Contents 1 x 5dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 1.65kgs / 3.64lb One Package Size 31cm * 23cm * 11cm / 12.2inch * 9.06inch * 4.33inch Qty per Carton 4 Carton Weight 7.40kgs / 16.31lb Carton Size 48cm * 33cm * 24cm / 18.9inch * 12.99inch * 9.45inch Loading Container 20GP: 701 cartons * 4 pcs = 2804 pcs40HQ: 1628 cartons * 4 pcs = 6512 pcs
£48.99
1. Made by high quality ABS elastic cable 2. Stop phone loss and theft, prevent costly phone replacements 3. After attaching the lock to the wall/table 4. Wide range Application: Retail chain store or exhibition center 5. Note: Without alarm functionSpecification: General Compatible with Apple: iPhone 4S, iPod touch 4, iPhone 4(CDMA), iPhone 4, iPod touch 3, iPod touch 2, iPod touch Package Weight One Package Weight 0.07kgs / 0.15lb One Package Size 12cm * 3cm * 2.5cm / 4.72inch * 1.18inch * 0.98inch Qty per Carton 360 Carton Weight 21.60kgs / 47.62lb Carton Size 46cm * 30cm * 30cm / 18.11inch * 11.81inch * 11.81inch Loading Container 20GP: 644 cartons * 360 pcs = 231840 pcs40HQ: 1495 cartons * 360 pcs = 538200 pcs
£2.99 £1.99
Vous avez vu 552 produits sur 642
🛡️ Secure Smarter, Pay Less! 🛡️ Get direct-sourced security accessories at wholesale prices — no middleman, just massive savings! 🔍 Direct from source | No MOQ | Wholesale for everyone! 📦 Ready to ship – stock up today!
Explore our wide range:
📹 IP Cameras
🔌 CCTV Accessories
🚨 Security Alarms
🧍 Personal Security
🔔 Doorbells
🔐 Access Control Systems
📼 Video Recorders
🎥 Video Accessories
📡 Signal Detectors
📶 Signal Boosters
🛑 Signal Isolators
🔗 BNC Cable Adapters