Produits
Afficher les produits précédents
-
Mira Sales (Wholesale Direct Factory Prices) Mobile LED GSM 980MHz Signal Booster / Signal Repeater with Sucker Antenna, LED GSM980
About Signal BoosterCell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save a life. Unfortunately, there are still some places where one can find themselves - out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: parking lots, tunnels, big stores, office buildings, cars, boats, house in remote areas, etc. Here we will bring you a new kind of LED signal booster. Welcome to buy!Features1. High-gain linear power amplifier. 2. ALC and AGC function technology. 3. Ultra-low noise receive amplifier. 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters. 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications. 7. With full-duplex communication mode. 8. It explores an effective and reasonable method to dispel the heat.Installation Steps1. Use your mobile phone to test signal strength outside house or on roof, -70dBm is the basic requirement (full bar). 2. Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Mount your indoor antenna with signal repeater. 5. Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Notices1. Connect outdoor (BTS) port with outdoor antenna. Connect indoor ANT (MS) port with indoor antenna. Outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away at least from each other. 2. Indoor and outdoor antennas must be separated by wall. 3. If the signal is still weak after installation, please check whether or not the outdoor antenna is pointed to signal tower correctly or elsewhere with stronger signal and confirm that the signal strength achieved -70dBm. 4. If no signal for a long time after installation, please check the device power adapter whether or not connected perfectly and connectors connect well. 5. If strength is not steady, please check if outdoor and indoor antennas are too close. Please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 6. Packed the outdoor connector by waterproof glue, otherwise wet condition will reduce the signal cover area.Specification: General Frequency Range GSM 900MHz, Uplink 890-915MHz, Downlink 935-960MHz Gain Uplink 63-67dB, Downlink 63-67dB Output Power Uplink 15-19dBm, Downlink 15-19dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC:100~240V, 50/60Hz; DC:12V 2A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 198 x 186 x 20mm Weight 1200g Package Include Package Contents 1 x 5dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 1.39kgs / 3.07lb One Package Size 31cm * 20cm * 11cm / 12.2inch * 7.87inch * 4.33inch Qty per Carton 4 Carton Weight 7.40kgs / 16.31lb Carton Size 42cm * 33cm * 24cm / 16.54inch * 12.99inch * 9.45inch Loading Container 20GP: 801 cartons * 4 pcs = 3204 pcs40HQ: 1861 cartons * 4 pcs = 7444 pcs
£29.99
-
Mira Sales Mobile LED GSM 980MHz Signal Booster / Signal Repeater with Yagi Antenna, LED GSM Antenna
About Signal BoosterCell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save a life. Unfortunately, there are still some places where one can find themselves - out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: parking lots, tunnels, big stores, office buildings, cars, boats, house in remote areas, etc. Here we will bring you a new kind of LED signal booster. Welcome to buy!Features1. High-gain linear power amplifier. 2. ALC and AGC function technology. 3. Ultra-low noise receive amplifier. 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters. 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications. 7. With full-duplex communication mode. 8. It explores an effective and reasonable method to dispel the heat.Installation Steps1. Use your mobile phone to test signal strength outside house or on roof, -70dBm is the basic requirement (full bar). 2. Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Mount your indoor antenna with signal repeater. 5. Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Notices1. Connect outdoor (BTS) port with outdoor antenna. Connect indoor ANT (MS) port with indoor antenna. Outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away at least from each other. 2. Indoor and outdoor antennas must be separated by wall. 3. If the signal is still weak after installation, please check whether or not the outdoor antenna is pointed to signal tower correctly or elsewhere with stronger signal and confirm that the signal strength achieved -70dBm. 4. If no signal for a long time after installation, please check the device power adapter whether or not connected perfectly and connectors connect well. 5. If strength is not steady, please check if outdoor and indoor antennas are too close. Please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 6. Packed the outdoor connector by waterproof glue, otherwise wet condition will reduce the signal cover area.Specification: General Frequency Range GSM 900MHz, Uplink 890-915MHz, Downlink 935-960MHz Gain Uplink 63-67dB, Downlink 63-67dB Output Power Uplink 15-19dBm, Downlink 15-19dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC:100~240V, 50/60Hz; DC:12V 2A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 198 x 186 x 20mm Weight 1200g Package Include Package Contents 1 x 12dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 2.36kgs / 5.21lb One Package Size 52cm * 26cm * 15cm / 20.47inch * 10.24inch * 5.91inch Qty per Carton 2 Carton Weight 5.60kgs / 12.35lb Carton Size 54cm * 28cm * 32cm / 21.26inch * 11.02inch * 12.6inch Loading Container 20GP: 551 cartons * 2 pcs = 1102 pcs40HQ: 1279 cartons * 2 pcs = 2558 pcs
£30.99
-
Mira Sales (Wholesale Direct Factory Prices) Mobile LED WCDMA 2100MHz & GSM 900MHz Signal Booster / Signal Repeater with Logarithm Periodic Antenna
About Signal BoosterCell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save a life. Unfortunately, there are still some places where one can find themselves - out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: parking lots, tunnels, big stores, office buildings, cars, boats, house in remote areas, etc. Here we will bring you a new kind of LED signal booster. Welcome to buy!Features1. High-gain linear power amplifier. 2. ALC and AGC function technology. 3. Ultra-low noise receive amplifier. 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters. 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications. 7. With full-duplex communication mode. 8. It explores an effective and reasonable method to dispel the heat.Installation Steps1. Use your mobile phone to test signal strength outside house or on roof, -70dBm is the basic requirement (full bar). 2. Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Mount your indoor antenna with signal repeater. 5. Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Notices1. Connect outdoor (BTS) port with outdoor antenna. Connect indoor ANT (MS) port with indoor antenna. Outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away at least from each other. 2. Indoor and outdoor antennas must be separated by wall. 3. If the signal is still weak after installation, please check whether or not the outdoor antenna is pointed to signal tower correctly or elsewhere with stronger signal and confirm that the signal strength achieved -70dBm. 4. If no signal for a long time after installation, please check the device power adapter whether or not connected perfectly and connectors connect well. 5. If strength is not steady, please check if outdoor and indoor antennas are too close. Please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 6. Packed the outdoor connector by waterproof glue, otherwise wet condition will reduce the signal cover area.Specification: General Frequency Range WCDMA 2100MHz, Uplink 1920-1980MHz, Downlink 2110-2170MHz, GSM 900MHz, Uplink 890-915MHz, Downlink 935-960MHz Gain 65dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Automatic Gain Control >20dB Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <2 MTBF >50000h Power Supply AC:90~265V, 50/60Hz; DC:12V 2A Power Consumption <20W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 198 x 182 x 20mm Weight 1200g Package Include Package Contents 1 x 9dB Outdoor Antenna 1 x 5dB Indoor Antenna 1 x 5m RG6-50 OHM Indoor Coaxial Cable 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 4.95kgs / 10.92lb One Package Size 43cm * 22cm * 24cm / 16.93inch * 8.66inch * 9.45inch Qty per Carton 4 Carton Weight 13.40kgs / 29.54lb Carton Size 46cm * 46cm * 50cm / 18.11inch * 18.11inch * 19.69inch Loading Container 20GP: 252 cartons * 4 pcs = 1008 pcs40HQ: 585 cartons * 4 pcs = 2340 pcs
£47.99
-
Mira Sales (Wholesale Direct Factory Prices) Mobile LED WCDMA 2100MHz & GSM 900MHz Signal Booster / Signal Repeater with Sucker Antenna, WCDMA&GSM
About Signal BoosterCell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save a life. Unfortunately, there are still some places where one can find themselves - out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: parking lots, tunnels, big stores, office buildings, cars, boats, house in remote areas, etc. Here we will bring you a new kind of LED signal booster. Welcome to buy!Features1. High-gain linear power amplifier. 2. ALC and AGC function technology. 3. Ultra-low noise receive amplifier. 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters. 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications. 7. With full-duplex communication mode. 8. It explores an effective and reasonable method to dispel the heat.Installation Steps1. Use your mobile phone to test signal strength outside house or on roof, -70dBm is the basic requirement (full bar). 2. Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Mount your indoor antenna with signal repeater. 5. Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Notices1. Connect outdoor (BTS) port with outdoor antenna. Connect indoor ANT (MS) port with indoor antenna. Outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away at least from each other. 2. Indoor and outdoor antennas must be separated by wall. 3. If the signal is still weak after installation, please check whether or not the outdoor antenna is pointed to signal tower correctly or elsewhere with stronger signal and confirm that the signal strength achieved -70dBm. 4. If no signal for a long time after installation, please check the device power adapter whether or not connected perfectly and connectors connect well. 5. If strength is not steady, please check if outdoor and indoor antennas are too close. Please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 6. Packed the outdoor connector by waterproof glue, otherwise wet condition will reduce the signal cover area.Specification: General Frequency Range WCDMA 2100MHz, Uplink 1920-1980MHz, Downlink 2110-2170MHz, GSM 900MHz, Uplink 890-915MHz, Downlink 935-960MHz Gain 65dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Automatic Gain Control >20dB Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <2 MTBF >50000h Power Supply AC:90~265V, 50/60Hz; DC:12V 2A Power Consumption <20W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 198 x 182 x 20mm Weight 1200g Package Include Package Contents 1 x 9dB Outdoor Antenna 1 x 5dB Indoor Antenna 1 x 5m RG6-50 OHM Indoor Coaxial Cable 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 3.78kgs / 8.34lb One Package Size 39cm * 22cm * 20cm / 15.35inch * 8.66inch * 7.87inch Qty per Carton 4 Carton Weight 15.90kgs / 35.05lb Carton Size 51cm * 45cm * 45cm / 20.08inch * 17.72inch * 17.72inch Loading Container 20GP: 258 cartons * 4 pcs = 1032 pcs40HQ: 599 cartons * 4 pcs = 2396 pcs
£44.99
-
Mira Sales WCDMA 2100MHz Mobile Phone Signal Booster / LCD Signal Repeater with Sucker Antenna
About The Product: This LCD micro-repeater kit includes an outdoor and indoor antenna, suitable for mobile phone signal boosting, presenting good amplification effect with no blind spot, which is widely used at home, office, meeting room and other small places. Note: Please ensure your phone frequency the same with our repeater before purchase, for different phone may use different frequency. Features: 1. Mini WCDMA 2100MHz LCD repeater for mobile phone signal boosting. 2. With LCD indicator to show real-time work state. 3. ALC function, no interference to work station. 4. Low noise, low heat, low power consumption. 5. Alloy material, durable in performance. 6. Perfect design, easy installation. 7. Antenna gain: 5dB outdoor antenna, 3dB indoor antenna. 8. Outdoor antenna length: 10m/32.81ft.Specification: General Model WCDMA 2100MHz Material Aluminum Alloy Frequency Range Uplink 1920-1980MHz, Downlink 2110-2170MHz Gain Uplink 65dB, Downlink 70dB Output Power Uplink 23dBm, Downlink 23dBm Power Supply DC5V/2A (AC110-240V) Impedance 50ohm RF Connector N-Female Outdoor Antenna Length 10m Dimensions & Weight Size 16.3*10.4*2cm Package Include Package Contents 1 x 5dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x Manual 1 x Signal Booster Package Weight One Package Weight 0.90kgs / 1.98lb One Package Size 30cm * 20cm * 5cm / 11.81inch * 7.87inch * 1.97inch Qty per Carton 10 Carton Weight 11.00kgs / 24.25lb Carton Size 52cm * 42cm * 32cm / 20.47inch * 16.54inch * 12.6inch Loading Container 20GP: 381 cartons * 10 pcs = 3810 pcs40HQ: 885 cartons * 10 pcs = 8850 pcs
£21.99
-
Mira Sales (Wholesale Direct Factory Prices) WCDMA 2100MHz Signal Booster / 3G Signal Repeater with Sucker Antenna, 2100MHz Signal Booster
Why to use1. Cell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save life of somebody. 2. Unfortunately, there are still some places where one can find themselves out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: 1) Parking lots, tunnels 2) Big stores, office buildings 3) Cars, boats etc. 4) House in remote areas etcFeatures1. High-gain linear power amplifier 2. ALC and AGC function technology 3. Ultra-low noise receive amplifier 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications 7. With full-duplex communication mode. 8. Dispel the heat effective reasonable, the structure is pretty, the volume is suitableHow to work1. The outside antenna catches the low signal from the mobile base station and delivers it to the cell phone amplifier through the connection cable (coax). 2. After the signal is accepted by the phone amplifier, the device amplifies it. 3. Then this amplified signal goes through the connection cable (coax) to the inside antenna. 4. And after that, the amplified signal transmits to the cell phoneHow to install1. Step 1: Use your mobile phone to test signal strength outside house or on roof, -70dbm is the basic requirement (full bar). 2. Step 2: Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Step 3: Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Step 4: Mount your indoor antenna with signal repeater 5. Step 5: Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signalNotes1. Connect outdoor (BTS) port with outdoor antenna, connect indoor ANT(MS) port with indoor antenna, outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away from each other at least. 2. Indoor and outdoor antenna must be separated by wallTechnique supports1. If still weak signal receipt after installation, please check if outdoor antenna point to signal tower correctly or elsewhere has stronger signal and confirm signal strength achieve-70DBM. 2. If still have no signal after installation, please check our device power adapter whether connected perfectly? And connectors connect well. 3. If strength is not steady, please check if outdoor and indoor antenna is too close; please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 4. Packed the outdoor connector by waterproof glue, otherwise wet reduce the signal cover areaSpecification: General Frequency Range WCDMA 2100MHz, Uplink 1920-1980MHz, Downlink 2110-2170MHz Gain Uplink 53-57dB, Downlink 58-62dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC: 100~240V, 50/ 60Hz; DC: 5V 2A Power Consumption <5W RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 100mm x 45mm x 18mm Weight 350g Package Include Package Contents 1 x 12dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 5m RG6-50 OHM Indoor Coaxial Cable 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 1.00kgs / 2.20lb One Package Size 51cm * 18cm * 13cm / 20.08inch * 7.09inch * 5.12inch Qty per Carton 4 Carton Weight 5.20kgs / 11.46lb Carton Size 53cm * 38cm * 28cm / 20.87inch * 14.96inch * 11.02inch Loading Container 20GP: 472 cartons * 4 pcs = 1888 pcs40HQ: 1097 cartons * 4 pcs = 4388 pcs
£28.99
-
Mira Sales (Wholesale Direct Factory Prices) WCDMA 2100MHz Signal Booster / 3G Signal Repeater with Yagi Antenna, Signal Booster
Why to use1. Cell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save life of somebody. 2. Unfortunately, there are still some places where one can find themselves out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: 1) Parking lots, tunnels 2) Big stores, office buildings 3) Cars, boats etc. 4) House in remote areas etcFeatures1. High-gain linear power amplifier 2. ALC and AGC function technology 3. Ultra-low noise receive amplifier 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications 7. With full-duplex communication mode. 8. Dispel the heat effective reasonable, the structure is pretty, the volume is suitableHow to work1. The outside antenna catches the low signal from the mobile base station and delivers it to the cell phone amplifier through the connection cable (coax). 2. After the signal is accepted by the phone amplifier, the device amplifies it. 3. Then this amplified signal goes through the connection cable (coax) to the inside antenna. 4. And after that, the amplified signal transmits to the cell phoneHow to install1. Step 1: Use your mobile phone to test signal strength outside house or on roof, -70dbm is the basic requirement (full bar). 2. Step 2: Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Step 3: Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Step 4: Mount your indoor antenna with signal repeater 5. Step 5: Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signalNotes1. Connect outdoor (BTS) port with outdoor antenna, connect indoor ANT(MS) port with indoor antenna, outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away from each other at least. 2. Indoor and outdoor antenna must be separated by wallTechnique supports1. If still weak signal receipt after installation, please check if outdoor antenna point to signal tower correctly or elsewhere has stronger signal and confirm signal strength achieve-70DBM. 2. If still have no signal after installation, please check our device power adapter whether connected perfectly? And connectors connect well. 3. If strength is not steady, please check if outdoor and indoor antenna is too close; please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 4. Packed the outdoor connector by waterproof glue, otherwise wet reduce the signal cover areaSpecification: General Frequency Range WCDMA 2100MHz, Uplink 1920-1980MHz, Downlink 2110-2170MHz Gain Uplink 53-57dB, Downlink 58-62dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC: 100~240V, 50/ 60Hz; DC: 5V 2A Power Consumption <5W RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 100mm x 45mm x 18mm Weight 350g Package Include Package Contents 1 x 12dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 5m RG6-50 OHM Indoor Coaxial Cable 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 1.59kgs / 3.51lb One Package Size 51cm * 18cm * 13cm / 20.08inch * 7.09inch * 5.12inch Qty per Carton 4 Carton Weight 5.75kgs / 12.67lb Carton Size 53cm * 38cm * 28cm / 20.87inch * 14.96inch * 11.02inch Loading Container 20GP: 472 cartons * 4 pcs = 1888 pcs40HQ: 1097 cartons * 4 pcs = 4388 pcs
£31.99
Vous avez vu 31 produits sur 31