Resultados de la búsqueda de "wifi range extender"

Features1. High-gain linear power amplifier 2. ALC and AGC function technology 3. Ultra-low noise receive amplifier 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters 5. Stable and reliable electromagnetic compatibility design 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications 7. With full-duplex communication mode 8. Dispel the heat effective reasonable, the structure is pretty, the volume is suitableInstall Repeater1. Step 1: Use your mobile phone to test signal strength outside house or on roof, -70dbm is the basic requirement (full bar) 2. Step 2 Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal 3. Step3: Run outdoor coaxial cable into building in a convenient location to connect with signal repeater 4. Step 4: Mount your indoor antenna with signal repeater 5. Step 5: Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal 6. Note: Connect outdoor (BTS) port with outdoor antenna, connect indoor ANT(MS) port with indoor antenna, outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away from each other at least 7. Indoor and outdoor antenna must be separated by wallWorking1. The outside antenna catches the low signal from the mobile base station and delivers it to the cell phone amplifier through the connection cable (coax) 2. After the signal is accepted by the phone amplifier, the device amplifies it 3. Then this amplified signal goes through the connection cable (coax) to the inside antenna 4. And after that, the amplified signal transmits to the cell phoneTechnique Supporting1. If still weak signal receipt after installation, please check if outdoor antenna point to signal tower correctly or elsewhere has stronger signal and confirm signal strength achieve-70DBM. 2. If still have no signal after installation, please check our device power adapter whether connected perfectly? And connectors connect well. 3. If strength is not steady, please check if outdoor and indoor antenna is too close; please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 4. Packed the outdoor connector by waterproof glue, otherwise wet reduce the signal cover areaSpecification: General Frequency Range CDMA 850MHz, Uplink 824-849MHz, Downlink 869-894MHz Gain Uplink 58-62dB, Downlink 58-62dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC: 100~240V, 50/ 60Hz; DC: 5V 1A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 140mm x 98mm x 20mm Weight 280g Package Include Package Contents 1 x 12dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 5m RG6-50 OHM Indoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual 1 x Signal Booster Package Weight One Package Weight 1.39kgs / 3.07lb One Package Size 51cm * 25cm * 10cm / 20.08inch * 9.84inch * 3.94inch Qty per Carton 6 Carton Weight 10.00kgs / 22.05lb Carton Size 52cm * 52cm * 32cm / 20.47inch * 20.47inch * 12.6inch Loading Container 20GP: 308 cartons * 6 pcs = 1848 pcs40HQ: 715 cartons * 6 pcs = 4290 pcs

Leer Más Menos

1. High security level, support WPA/WPA2 encryption, effectively prevent various virus attacks2. 10 devices can be connected at the same time, stable connection, not easy to fall, the device will not heat up3. SIM card plug and play4. One button start, simple and convenient5. Transmission rate: up to 150Mbps6. Interface: Type-C7. Battery capacity: 3000mAh8. Eurasia version support Europe/Asia/Africa: 4G LTE B1/B3/B7/B8/B20(2600/2100/1800/900/850/800MHZ )+TDD B38/B40/B41(2600/2300/2500MHZ)9. Size: about 9.8 x 5.8 x 2cmSpecification: Package Weight One Package Weight 0.15kgs / 0.34lb One Package Size 15cm * 13cm * 5cm / 5.91inch * 5.12inch * 1.97inch Qty per Carton 100 Carton Weight 15.50kgs / 34.17lb Carton Size 61cm * 31cm * 28cm / 24.02inch * 12.2inch * 11.02inch Loading Container 20GP: 503 cartons * 100 pcs = 50300 pcs40HQ: 1169 cartons * 100 pcs = 116900 pcs

Leer Más Menos

1. Suitable for desktop computers 2. Support 2.4GHz/5.8GHz/6GHz tri-band, signal transmission road is smoother 3. The transmission rate can reach 5374Mbps 4. WPA3 encryption to protect privacy 5. Bluetooth 5.2 standard, longer transmission distance, better stability, can connect to Bluetooth devices arbitrarily 6. Strong antenna means strong signal 7. Support operating system: Windows 10 (64-bit) 8. Interface type: PCI-E (compatible with PCI-E X1/X4/X8/X16) 9. Wireless standard: support IEEE 802.11 a/b/g/n/ac/ax standard 10. Wireless rate: 2.4GHz: 574Mpbs, 5.8GHz: 2400Mpbs, 6GHz: 2400Mpbs 11. Encryption method: WPA2/WPA3Specification: General Certificate CE, RED Package Weight One Package Weight 0.31kgs / 0.68lb One Package Size 29cm * 12cm * 3cm / 11.42inch * 4.72inch * 1.18inch Qty per Carton 60 Carton Weight 19.00kgs / 41.89lb Carton Size 50cm * 47cm * 31cm / 19.69inch * 18.5inch * 12.2inch Loading Container 20GP: 366 cartons * 60 pcs = 21960 pcs40HQ: 849 cartons * 60 pcs = 50940 pcs

Leer Más Menos

1. Interface: PCI-Express. 2. Antenna: 4x5dBi 0mni directional detachable antenna. 3. Standard: IEEE 802.11ac, IEEE 802.11a, IEEE 802.11n, IEEE 802.11g, IEEE 802.11b. 4. Frequency: 5.180-5.240 GHz, 5.745-5.825 GHz / 2.4 GHz - 2.484 GHz. 5. Rate: 5GHz: 11ac: Up to 1300Mbps (dynamic), 2.4GHz: 11n: Up to 600Mbps (dynamic). 6. 5GHz receiving sensitivity: 11a 6Mbps: -85dBm. 11a 54Mbps: -68dBm. 11ac HT20: -59dBm. 11ac HT40: -54dBm. 11ac HT80: -51dBm. 7. 2.4GHz receiving sensitivity: 11b 11Mbps: -80dBm. 11g 54Mbps: -68dBm. 11n HT20: -64dBm. 11n HT40: -61dBm. 8. Transmit power: less than 20dBm (EIRP). 9. Wireless mode: Ad-Hoc / Infrastructure mode. 10. Security: Support 64/128 bit WEP, WPA-PSK / WPA2-PSK, 802.1x. 11. Modulation: DBPSK, DQPSK, CCK, OFDM, 16-QAM, 64-QAM, 256-QAM. 12. Operating system support: Windows 10, Windows 8.1, Windows 8, Windows 7, Windows XP. 13. Working temperature: 0-40 degrees Celsius. 14. Storage temperature: -40-70 degrees Celsius. 15. Operating humidity: 10% to 90% does not condense. 16. Storage humidity: 5 to 90 percent does not condense. Follow these steps to insert the adapter into your computer: 1. Turn off your computer and connect the power cord and other attached peripherals to your computer. 2. Remove the outer casing panel. Locate the available PCl-E slot and remove its slot cover. 3. Carefully insert the adapter into the PCl-E slot and secure it with the captive screws. 4. Replace the panel housing. 5. Install the antenna. 6. Reconnect the power cord and turn on the computer.Specification: Package Weight One Package Weight 0.29kgs / 0.63lb One Package Size 18.6cm * 13.5cm * 4.2cm / 7.32inch * 5.31inch * 1.65inch Qty per Carton 48 Carton Weight 14.20kgs / 31.31lb Carton Size 42cm * 44cm * 40cm / 16.54inch * 17.32inch * 15.75inch Loading Container 20GP: 360 cartons * 48 pcs = 17280 pcs40HQ: 837 cartons * 48 pcs = 40176 pcs

Leer Más Menos

1. Product material: ABS material + gold-plated USB head 2. Product chip: Realtek 8811CU 3. Network speed support: 2.4G--150Mpbs/5G---433Mpbs 4. Network mode: dual band 2.4G+5.8G 5. Applicable system: Windows, Linux, MAC (After installing the driver, all system versions are supported) 6. USB head size: 4.5x2x1.2cm 7. Antenna size: 10.8cm 8. Bare metal weight: 12g 9. Bare metal + disc weight: 18gSpecification: Package Weight One Package Weight 0.04kgs / 0.09lb One Package Size 15cm * 10cm * 2cm / 5.91inch * 3.94inch * 0.79inch Qty per Carton 100 Carton Weight 3.90kgs / 8.60lb Carton Size 32cm * 22cm * 52cm / 12.6inch * 8.66inch * 20.47inch Loading Container 20GP: 728 cartons * 100 pcs = 72800 pcs40HQ: 1691 cartons * 100 pcs = 169100 pcs

Leer Más Menos

1. Tri-band High-Speed Transmission: Supports a wireless transmission rate of 6452Mbps. The tri-band design automatically switches according to the network environment, meeting the high-speed network requirements of HD video, large-scale games, and other applications. 2. M.2 Interface Compatibility: Adopts the M.2 interface specification, perfectly compatible with mainstream laptop devices. Installation is convenient; simply replace or add a new chip for immediate use. 3. MediaTek Chip Support: Equipped with a MediaTek MT7925B22M chip, ensuring stable signal reception and strong anti-interference capabilities, improving wireless network connection quality. 4. Bluetooth 5.4 Version: Adopts the Bluetooth 5.4 standard, effectively extending the transmission distance and enhancing anti-interference capabilities, providing a stable and smooth connection experience. 5. Dual MAC Address Design: Equipped with separate WF MAC and BT MAC addresses, allowing for independent operation of WiFi and Bluetooth functions, resulting in more organized device connections. 6. Industrial-Grade Construction: Utilizes a green PCB board design with clearly labeled interface and parameter information, demonstrating solid construction and suitability for long-term stable use. Specifications 1. Hardware Specifications: MediaTek MT7925B22M 2. Bluetooth Version: BT5.4 3. Applicable Scope: Laptops 4. Interface Support: M.2 Interface 5. Wireless Speed: 2.4GHz: 574Mbps, 5GHz: 2882Mbps, Third Band: 2882Mbps 6. Operating Temperature: 0 degrees Celsius to 40 degrees Celsius 7. Storage temperature: -40 degrees Celsius to 70 degrees Celsius 8. Operating humidity: 10% - 90%RH, non-condensing 9. Storage humidity: 5% - 90%RH, non-condensingSpecification: Package Weight One Package Weight 0.23kgs / 0.52lb One Package Size 21cm * 12cm * 3.5cm / 8.27inch * 4.72inch * 1.38inch Qty per Carton 80 Carton Weight 18.30kgs / 40.34lb Carton Size 50cm * 36cm * 45cm / 19.69inch * 14.17inch * 17.72inch Loading Container 20GP: 329 cartons * 80 pcs = 26320 pcs40HQ: 764 cartons * 80 pcs = 61120 pcs

Leer Más Menos

1. Card reading distance 0-10m, adjustable power 18-26dBm 2. Built-in high-gain 9dBi antenna for wide coverage, sensitive card reading, and stable performance 3. Multiple communication interfaces and a separate cable design allow for connection to various devices, such as parking sensors and infrared detectors 4. Flexible switching between active, passive, and trigger modes 5. Integrated structure with IP65-rated waterproof and dustproof protection for easy operation in various outdoor environments 6. Wide range of applications: Suitable for warehousing and logistics, production line tracking, intelligent asset management, and access control systems Specifications: 1. Model: FI-806 2. Dimensions: 260mm x 260mm x 40mm 3. Weight: Approximately 1000g 4. Operating frequency: Standard ISM 902-928MHz and ISM 865-868MHz, optional 5. Operating protocol: ISO18000-6C (EPCGEN2) 6. Card Reading Distance: 0-10m 7. Card Reading Speed: Software-adjustable, average reading speed per 64 bits per card is less than 6ms 8. Output Power: 18-26dBm, software-adjustable 9. Operating Mode: Wide Frequency Hopping Spectrum (FHSS) 10. Antenna Gain: Built-in circularly polarized antenna, 9dBi gain 11. Communication Interfaces: RS232, RS485, RJ45, Wiegand 26/34, one trigger output, one relay output 12. Operating Indicator: Buzzer 13. Power Supply: DC+12V (with power adapter), voltage range: 9-16V 14. Operating Temperature: -20 degrees Celsius to +80 degrees CelsiusSpecification: Package Weight One Package Weight 2.03kgs / 4.48lb One Package Size 42cm * 32cm * 12cm / 16.54inch * 12.6inch * 4.72inch Qty per Carton 10 Carton Weight 21.00kgs / 46.30lb Carton Size 46cm * 38cm * 40cm / 18.11inch * 14.96inch * 15.75inch Loading Container 20GP: 381 cartons * 10 pcs = 3810 pcs40HQ: 885 cartons * 10 pcs = 8850 pcs

Leer Más Menos

About Signal BoosterCell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save a life. Unfortunately, there are still some places where one can find themselves - out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: parking lots, tunnels, big stores, office buildings, cars, boats, house in remote areas, etc. Here we will bring you a new kind of LED DCS signal booster. Welcome to buy!Features1. High-gain linear power amplifier. 2. ALC and AGC function technology. 3. Ultra-low noise receive amplifier. 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters. 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications. 7. With full-duplex communication mode. 8. It explores an effective and reasonable method to dispel the heat.Installation Steps1. Use your mobile phone to test signal strength outside house or on roof, -70dBm is the basic requirement (full bar). 2. Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Mount your indoor antenna with signal repeater. 5. Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Notices1. Connect outdoor (BTS) port with outdoor antenna. Connect indoor ANT (MS) port with indoor antenna. Outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away at least from each other. 2. Indoor and outdoor antennas must be separated by wall. 3. If the signal is still weak after installation, please check whether or not the outdoor antenna is pointed to signal tower correctly or elsewhere with stronger signal and confirm that the signal strength achieved -70dBm. 4. If no signal for a long time after installation, please check the device power adapter whether or not connected perfectly and connectors connect well. 5. If strength is not steady, please check if outdoor and indoor antennas are too close. Please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 6. Packed the outdoor connector by waterproof glue, otherwise wet condition will reduce the signal cover area.Specification: General Frequency Range DCS 1800MHz, Uplink 1710-1785MHz, Downlink 1805-1880MHz Gain Uplink 63-67dB, Downlink 63-67dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC:100~240V, 50/60Hz; DC:12V 2A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 198 x 182 x 20mm Weight 1200g Package Include Package Contents 1 x 5dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 1.58kgs / 3.48lb One Package Size 31cm * 23cm * 11cm / 12.2inch * 9.06inch * 4.33inch Qty per Carton 4 Carton Weight 7.40kgs / 16.31lb Carton Size 48cm * 33cm * 24cm / 18.9inch * 12.99inch * 9.45inch Loading Container 20GP: 701 cartons * 4 pcs = 2804 pcs40HQ: 1628 cartons * 4 pcs = 6512 pcs

Leer Más Menos

Feature1. Built-in wireless driver, installation without CD-ROM, get rid of the tedious wireless driver installation process 2. Support new generation of WiFi6, fast speed, low latency, large capacity, more secure 3. External 4 x 5dBi high-gain antennas with strong signal, provide better wireless penetration, whether it is games, video, audio, video, can be smooth and comfortable 4. Equipped 1.2M extension cable, more flexible placement, support USB3.0, backward compatible with USB2.0 and other interfaces 5. Compatible with mainstream Win 10/11 systems 6. Support for USB3.0, faster and more efficient transmission, and backward compatibility with USB2.0. Specifications1. Chipset: RTL8832BU 2. Antenna: With 4x5dBi high gain antenna 3. Wireless frequency: 2.412GHz-2.484GHz, 5.180-5.825GHz 4. Transmission rate: 1800Mbps 5. Wireless standards: IEEE 802.11a/b/g/n/ac/ax 6. Interface: USB3.0, USB2.0 7. Encryption: WPA2, WPA3 8. Support system: Windows 10 (32 bits , 64 bits), Windows 11(64 bits ) 9. Working environment: - Operating Temperature: 0-40 degree Celsius - Storage Temperature: -40~70 degree Celsius - Operating Humidity: 10%~90%RH No-condensing - Storage Humidity: 5%~90%RH No-condensing 10. Size: 101mmx98mmx175mmSpecification: General Certificate CE Package Weight One Package Weight 0.30kgs / 0.66lb One Package Size 27.7cm * 12.5cm * 5.8cm / 10.91inch * 4.92inch * 2.28inch Qty per Carton 80 Carton Weight 23.25kgs / 51.26lb Carton Size 61cm * 53cm * 59cm / 24.02inch * 20.87inch * 23.23inch Loading Container 20GP: 139 cartons * 80 pcs = 11120 pcs40HQ: 324 cartons * 80 pcs = 25920 pcs

Leer Más Menos

1. Suitable for desktop computers 2. Support 2.4GHz/5.8GHz/6GHz tri-band, signal transmission road is smoother 3. The transmission rate can reach 5374Mbps 4. WPA3 encryption to protect privacy 5. Bluetooth 5.2 standard, longer transmission distance, better stability, can connect to Bluetooth devices arbitrarily 6. Organ efficient heat dissipation design 7. Support operating system: Windows 10 (64-bit) 8. Interface type: PCI-E (compatible with PCI-E X1/X4/X8/X16) 9. Wireless standard: support IEEE 802.11 a/b/g/n/ac/ax standard 10. Wireless rate: 2.4GHz: 574Mpbs, 5.8GHz: 2400Mpbs, 6GHz: 2400Mpbs 11. Encryption method: WPA2/WPA3 12. Product size: 286x120mm 13. Antenna size: 200mmSpecification: General Certificate CE, RED Package Weight One Package Weight 0.31kgs / 0.68lb One Package Size 29cm * 12cm * 3cm / 11.42inch * 4.72inch * 1.18inch Qty per Carton 60 Carton Weight 19.00kgs / 41.89lb Carton Size 50cm * 47cm * 31cm / 19.69inch * 18.5inch * 12.2inch Loading Container 20GP: 366 cartons * 60 pcs = 21960 pcs40HQ: 849 cartons * 60 pcs = 50940 pcs

Leer Más Menos

Features:1. Anti-Recording and Eavesdropping Detection: Accurately detects hidden recording and listening devices, preventing private conversations from being illegally recorded or leaked.2. Wireless Signal Detection: Actively scans RF signals, transmitters, GPS trackers, wireless audio bugs, and Bluetooth-enabled devices for comprehensive monitoring.3. Infrared Scanning Detection: Equipped with an infrared night vision light and dedicated filter lens, allowing you to visually locate hidden pinhole cameras, quickly detect hidden cameras.4. Smart Alert Design: Built-in vibration alarm instantly notifies you when abnormal signals are detected, eliminating the need for constant monitoring.5. Long Battery Life: Low-power, energy-efficient design ensures extended standby time, reducing the need for frequent recharging.6. Compact and Portable: Lightweight and compact design fits easily into your pocket or bag, making it convenient to carry anywhere.8. Multi-Scenario Use: Suitable for use anytime, anywhere, providing all-day protection for your privacy and security.Specifications:1. Sensitivity Adjustment: 6 levels2. Key function: GPS signal detection, WiFi signal detection, Camera detection, Anti-eavesdropping detection, vibration alarm, Audible alarm, magnetic field detection, infrared detection3. LED Infrared Lights: 4 units4. Material: ABS + PC5. Charging Port: Type-C6. Battery Type: 5020407. Battery Capacity: 500mAh8. Rated Voltage: DC 5V 1A9. Charging Time: Approx. 2-3 hours10. Continuous Working Time: About 8 hours11. Operating Temperature: -10 degrees Celsius to 50 degrees Celsius12. Storage Temperature: -10 degrees Celsius to 70 degrees Celsius13. Humidity Range: 5% - 90% (Non-condensing)Package Contents:1. Detector x 12. User Manual x 13. Data Cable x 14. Color Box x 1Specification: Package Weight One Package Weight 0.09kgs / 0.20lb One Package Size 15cm * 10cm * 3cm / 5.91inch * 3.94inch * 1.18inch Qty per Carton 100 Carton Weight 9.50kgs / 20.94lb Carton Size 42cm * 28cm * 30cm / 16.54inch * 11.02inch * 11.81inch Loading Container 20GP: 755 cartons * 100 pcs = 75500 pcs40HQ: 1754 cartons * 100 pcs = 175400 pcs

Leer Más Menos

1. Motherboard chip: Qualcomm QCA9531 650Mhz clocked CPU; power amplifier chip: SE2576L; 64MDDR22. Antenna specifications: 2x14dBi smart dual-polarized antenna3. Wireless standard: support IEEE802.11b/g/n standard4. Radio frequency parameters: Transmitting power: 500mW (27dBm) Receiving sensitivity: -96dBm Working frequency: 802.11b/g/n: 2.3GHz-2.7GHz5. Wireless rate: 300Mbps6. Physical interface: 1 10/100Mbps WAN RJ45 Ethernet port; 1 10/100Mbps LAN RJ45 Ethernet port; 1 POE output toggle switch, 1 RESET button7. Indicator lights: 8 indicator lights8. Power supply: power supply mode: support 802.3af/802.3at compatible power supply; power adapter: 48V 0.32A POE power adapter;9. Power consumption: about 7W10. Installation method: pole-mounted installation, wall-mounted installation, bracket installation11. Product size: 262x80x53mm12. Product net weight: 322g13. Packing list: stainless steel cable tie, POE power supply, power cord, network bridge, installation guideSpecification: Package Weight One Package Weight 1.57kgs / 3.46lb One Package Size 34cm * 12cm * 16cm / 13.39inch * 4.72inch * 6.3inch Qty per Carton 10 Carton Weight 16.40kgs / 36.16lb Carton Size 45cm * 37cm * 35cm / 17.72inch * 14.57inch * 13.78inch Loading Container 20GP: 457 cartons * 10 pcs = 4570 pcs40HQ: 1062 cartons * 10 pcs = 10620 pcs

Leer Más Menos