Resultados de la búsqueda de "switch controller accessories"

L76X Multi-GNSS HAT for Raspberry Pi, Supports GPS, BDS, QZSSOverview1. This is a Raspberry Pi GNSS HAT which supports Multi-GNSS systems: GPS, BDS, and QZSS, with advantages such as fast positioning, high accuracy, low power consumption, and so on.2. It is an easy way to enable global positioning function for your Raspberry Pi.Features1. Support Multi-GNSS systems: GPS, BDS, and QZSS2. EASY, self track prediction technology, help quick positioning2. AlwaysLocate, intelligent controller of periodic mode for power saving3. Support DGPS, SBAS (WAAS/EGNOS/MSAS/GAGAN)4. UART communication baudrate: 4800~115200bps (9600bps by default)5. Onboard battery holder, supports ML1220 rechargeable battery, for preserving ephemeris information and hot starts6. 4x LEDs for indicating the module working status7. Come with development resources and manual (examples for Raspberry Pi/Arduino/STM32)GNSS Specifications1. Band: GPS L1(1575.42Mhz), BD2 B1 (1561.098MHz)- Channels: 33 tracking ch, 99 acquisition ch, 210 PRN ch- C/A code- SBA: WAAS, EGNOS, MSAS, GAGAN2. Horizontal position accuracy:- Autonomous: <2.5mCEP3. Time-To-First-Fix @-130dBm (EASY? enabled):- Cold starts: <15s- Warm starts: <5s- Hot starts: <1s4. Sensitivity:- Acquisition: -148dBm- Tracking: -163dBm- Re-acquisition: -160dBm5. Dynamic performance:- Altitude (max): 18000m- Velocity (max): 515m/s- Acceleration (max): 4GGeneral Specifications1. Communication interface: UART2. Baudrate: 4800~115200bps (9600bps by default)3. Update rate: 1Hz (default), 10Hz (max)4. Protocols: NMEA 0183, PMTK5. Power supply voltage: 5V / 3.3V6. Operating current: 13mA7. Operating temperature: -40 degree C ~ 85 degree C8. Dimensions: 65mm x 30.5mmApplications1. Vehicle tracking2. Asset tracking3. Security system4. Industrial PDA5. GIS applicationWhat is on Board1. L76B module2. CP2102: USB TO UART converter3. CAT24C32: EEPROM4. RT9193-33: Power manager5. Backup mode wakeup button6. Standby switch7. Indicators:- RXD/TXD: UART RX/TX indicator- PPS: GPS status indicator- PWR: Power indicator8. Raspberry Pi GPIO connector: For connecting with Raspberry Pi9. USB TO UART port10. GNSS antenna connector11. Battery holder: Support ML1220 rechargeable battery, for preserving ephemeris information and hot starts12. UART selection jumpers- A: control the L76B through USB TO UART- B: control the L76B through Raspberry Pi- C: access Raspberry Pi through USB TO UARTPackage Contents1. L76X GPS HAT x12. GPS External Antenna (B) x13. USB type A plug to micro plug cable x14. RPi screws pack (2pcs) x15. 2x20PIN pinheader x1Specification: Package Weight One Package Weight 0.15kgs / 0.33lb One Package Size 10cm * 6cm * 2cm / 3.94inch * 2.36inch * 0.79inch Qty per Carton 720 Carton Weight 15.00kgs / 33.07lb Carton Size 60cm * 36cm * 40cm / 23.62inch * 14.17inch * 15.75inch Loading Container 20GP: 308 cartons * 720 pcs = 221760 pcs40HQ: 716 cartons * 720 pcs = 515520 pcs

Leer Más Menos

1. Bluetooth device name: YP042. Bluetooth chip model: AC6956A43. Bluetooth version: V5.14. Bluetooth transmission distance: about 10 meters5. Power supply interface: USB6. Audio output interface: 3.5mm7. Call function: support, USBA male connector built-in silicon microphone8. Working voltage: 3.6-5.5V9. Working current: 20mA10. Indicator status: After USB power supply, the green light flashes quickly, and after the Bluetooth connection is successful, the green light flashes slowly11. Frequency response: 20Hz-20KHz12. Size: about 0.5m in lengthFeatures:1. After USB power supply, the green light flashes quickly, and after the Bluetooth connection is successful, the green light flashes slowly2. 3.5mm male audio output, suitable for car audio, ordinary audio and other audio equipment with Aux interface3. Enameled copper wire core, high-fidelity transmission, no noise, no current sound4. Bluetooth 5.1 master control, stable signal transmission, no delay and no freeze, listening to songs more smoothly5. Support mobile phone music and call functions, with car echo cancellation6. Support 1 drag 2 support, (connect 2 mobile phones at the same time, switch between two mobile phones at will, and share the music of two mobile phones)7. Automatic connection without power failure (automatic connection after the person leaves the car and returns)8. Built-in antenna design, can achieve 0-10m long-distance transmission9. The core wire is made of 6331 PP material, and the outer layer is made of TPU material and nylon braided wire, which is anti-winding, good elasticity, orderly and not messy10. Zinc alloy shell, good heat dissipation, non-hot, longer service lifeSpecification: Package Weight One Package Weight 0.03kgs / 0.07lb One Package Size 10cm * 8cm * 1cm / 3.94inch * 3.15inch * 0.39inch Qty per Carton 500 Carton Weight 17.00kgs / 37.48lb Carton Size 30cm * 50cm * 57cm / 11.81inch * 19.69inch * 22.44inch Loading Container 20GP: 311 cartons * 500 pcs = 155500 pcs40HQ: 724 cartons * 500 pcs = 362000 pcs

Leer Más Menos

RP2040-LCD-0.96 is a low-cost, high-performance Pico-like MCU board with flexible digital interfaces. It incorporates Raspberry Pi RP2040 microcontroller chip, as same as on Raspberry Pi Pico. For software development, either Raspberry Pi C/C++ SDK, or the MicroPython is available, which makes it easy for you to get started, and integrate it into end products quickly. In additional, there are also onboard 0.96inch IPS display, Lithium battery recharge/discharge header, and high efficiency DC-DC buck-boost chip. Key features include: 1. RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom 2. Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz 3. 264KB of SRAM, and 2MB of on-board Flash memory 4. USB-C connector, keeps it up to date, easier to use 5. 0.96 inch 160x80 pixels 65K colorful IPS LCD display 6. Lithium battery recharge/discharge header, suitable for mobile devices 7. Onboard DC-DC chip TPS63000, high efficiency DC-DC buck-boost chip, 1.8A current switch 8. Castellated module allows soldering direct to carrier boards (there should be dedicated cut-out for embedding the bottom components) 9. USB 1.1 with device and host support 10. Low-power sleep and dormant modes 11. Drag-and-drop programming using mass storage over USB 13. 26 x multi-function GPIO pins 14. 2 x SPI, 2 x I2C, 2 x UART, 3 x 12-bit ADC, 16 x controllable PWM channels 15. Accurate clock and timer on-chip 16. Temperature sensor 17. Accelerated floating-point libraries on-chip 18. 8 x Programmable I/O (PIO) state machines for custom peripheral supportSpecification: Package Weight One Package Weight 0.03kgs / 0.06lb One Package Size 15cm * 12cm * 2cm / 5.91inch * 4.72inch * 0.79inch Qty per Carton 500 Carton Weight 11.00kgs / 24.25lb Carton Size 52cm * 40cm * 39cm / 20.47inch * 15.75inch * 15.35inch Loading Container 20GP: 328 cartons * 500 pcs = 164000 pcs40HQ: 763 cartons * 500 pcs = 381500 pcs

Leer Más Menos

1. Material: ABS2. Chip: MT2503D3. Network: GSM/GPRS4. Frequency band: GSM 850/900/1800/1900MHz5. GPS positioning accuracy: 5m6. Alarm mode: vibration/power failure/movement/fence/overspeed alarm7. Battery: 70mAh polymer battery included8. Working voltage: 9-45V9. Uses: used for car positioning, logistics and transportation fleet management, etc.10. Dimensions: about 4.5x4x2.5 cm11. Weight: about 28gThe main function:1. GSM, GPS, Beidou positioning2. Switch between positioning mode and anti-detection mode3. Electronic fence4. Shift alarm5. Speeding alarm6. Vibration alarm7. Sleep power saving modeFeatures:1. Built-in GPS and GSM antenna2. The vehicle does not need to install a portable GPS locator, and the waterproof performance is IPX-63. Support mobile APP query function4. Read location information through B/S and mobile APP client5. Support SMS parameter setting and query function6. Support base station assisted positioning function, Beidou positioning function, support low power mode7. Support automatic storage of blind spots and make-up report function8. Support SMS alarm function9. Support historical track query within 180 days10. Built-in high-sensitivity vibration sensor, when the device feels the vibration of the vehicleSend an alarm prompt to the phone immediately11. OBD interface plug-in type, easy to install, suitable for cars with OBD interface12. Intelligently turn on the defense/disarm system, automatically obtain the vehicle status, and prevent and control the safety of the vehicleSpecification: Package Weight One Package Weight 0.06kgs / 0.14lb One Package Size 10cm * 5cm * 3cm / 3.94inch * 1.97inch * 1.18inch Qty per Carton 468 Carton Weight 30.00kgs / 66.14lb Carton Size 50cm * 50cm * 60cm / 19.69inch * 19.69inch * 23.62inch Loading Container 20GP: 177 cartons * 468 pcs = 82836 pcs40HQ: 412 cartons * 468 pcs = 192816 pcs

Leer Más Menos

Need more Flash for Raspberry Pi Pico? Dislike the outdated Micro USB connector? All these problems are solved by our RP2040-Plus now. As same as Raspberry Pi Pico, it incorporates the RP2040 microcontroller, with dual-core Arm Cortex M0+ processor running up to 133 MHz, and 26x multi-function GPIO pins. What is different, it features onboard 4MB Flash, USB-C connector, recharge header, and higher current DC-DC chip. Key features include: 1. RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom 2. Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz 3. 264KB of SRAM, and 4MB of on-board Flash memory 4. USB-C connector, keeps it up to date, easier to use 5. Lithium battery recharge/discharge header, suitable for mobile devices 6. Onboard DC-DC chip TPS63000, high efficiency DC-DC buck-boost chip, 1.8A current switch 7. Castellated module allows soldering direct to carrier boards 8. USB 1.1 with device and host support 9. Low-power sleep and dormant modes 10. Drag-and-drop programming using mass storage over USB 11. 26 x multi-function GPIO pins 12. 2 x SPI, 2 x I2C, 2 x UART, 3 x 12-bit ADC, 16 x controllable PWM channels 13. Accurate clock and timer on-chip 14. Temperature sensor 15. Accelerated floating-point libraries on-chip 16. 8 x Programmable I/O (PIO) state machines for custom peripheral supportSpecification: Package Weight One Package Weight 0.02kgs / 0.05lb One Package Size 15cm * 12cm * 2cm / 5.91inch * 4.72inch * 0.79inch Qty per Carton 500 Carton Weight 8.00kgs / 17.64lb Carton Size 52cm * 40cm * 39cm / 20.47inch * 15.75inch * 15.35inch Loading Container 20GP: 328 cartons * 500 pcs = 164000 pcs40HQ: 763 cartons * 500 pcs = 381500 pcs

Leer Más Menos

1. Product name: Xiaomi Router BE6500 2. Processor: Qualcomm Quad-core A53 1.1GHz CPU 3. Memory: 512MB 4. 2.4GHz Wi-Fi: 2X2 (theoretical rate can reach 688.2Mbps) 5. 5GHz Wi-Fi: 4x4 160MHz (theoretical rate can reach 5764.7Mbps) 6. Product antenna: 6 external high-gain Wi-Fi antennas 7. Product heat dissipation: natural heat dissipation 8. Dimensions: 318.8x46.9x242mm Complete machine interface 1. 10/100/1000/2500M adaptive WAN/LAN port x 4 2. Indicator light x 1 3. System reset button x 1 4. Power interface x 1 5. Mesh button x 1 Wireless parameters 1. Wi-Fi frequency band: dual-band, 2.4GHz and 5GHz 2. Wireless channel: 2.4GHz channel: 1,2,3,4,5,6,7,8,9,10,11,12,13 3. Wireless channel: 5GHz channel: 36,40,44,48,52,56,60,64,149,153,157,161,165 4. Protocol standard: IEEE 802.11a/b/g/n/ac/ax/be, IEEE 802.3/3u/3ab/3bz Software parameters 1. Operating system: MiWiFi ROM 2. Wireless security: WPA-PSK/WPA2-PSK/WPA3-SAE encryption, 3. Wireless access: control (black and white list), SSID hiding, intelligent anti-free network 4. Management application: support Web, Mijia App (Android & iOS) Product accessories 1. Router x 1 2. Network cable x 1 3. US power adapter x 1Specification: Package Weight One Package Weight 1.24kgs / 2.74lb One Package Size 33cm * 25cm * 6cm / 12.99inch * 9.84inch * 2.36inch Qty per Carton 10 Carton Weight 8.50kgs / 18.74lb Carton Size 52cm * 32cm * 34cm / 20.47inch * 12.6inch * 13.39inch Loading Container 20GP: 471 cartons * 10 pcs = 4710 pcs40HQ: 1094 cartons * 10 pcs = 10940 pcs

Leer Más Menos

1. Input voltage: 6.5-36V (the input voltage is lower than 6.5V, the current accuracy is inaccurate, and the LCD display is abnormal if it is lower than 5.5V)2. Output voltage: 1.2-32V, the default output is 5V step-down type, the output voltage can only be lower than the input voltage, and the voltage difference is more than 2V3. Output current: It can work stably at 3.5A for a long time, and it can reach about 4.5A with fan enhanced heat dissipation (adjustable limit current can reach about 4.2-4.5A)4. Output power: natural heat dissipation 50W (within 3.5A), plus fan to enhance heat dissipation 75W5. Voltage display: resolution 0.05V, range 1.2-32V6. Current display: resolution 0.005A, range 0-4.5A7. Conversion efficiency: about 94%, depending on the voltage difference and current efficiency8. Working current: about 30mA9. Input reverse polarity protection: yes10. Anti-backflow at the output: no (if charging the battery, first power on the module and then connect the battery, and ensure that the battery voltage is lower than the output voltage; if possible, connect an anti-backflow diode in series with the output positive pole)11. Short circuit protection: yes12. Size: about 70.5x48.4x28mm13. Weight: about 65g Features:1. Crystal shell, beautiful design, good touch texture of buttons, and output voltage set by button2. The button can control the output to turn off and on, and can set the power-on default to ON or OFF3. LCD can display input and output voltage, output current and output power4. The input terminal is protected against reverse connection, and the reverse connection will not burn5. High efficiency, high current, low heat generation, constant current value can be adjusted around 0-4.5A, suitable for office power supply, high-power LED constant current drive, lithium battery charging, etc.Function Description:1. There are IN/OUT and ON/OFF buttons on the left side of the module: the IN/OUT button switches the display of input voltage and output voltage, long press to switch the display of output current and output power; the ON/OFF button controls the output ON or OFF, long press Press to set the default output state is ON or OFF at the next power-on2. There are +/- two buttons on the right side of the module: + button press the output voltage to increase 0.05V, long press to continuously increase, and then long press to continuously increase 0.1V, 1V in slow steps; - button press the output voltage Decrease 0.05V, long press to continuously decrease, and then long press to continuously decrease 0.1V, 1V in slow steps3. ADJ-I is the current setting potentiometer. Turn clockwise to increase the set current. When the load current reaches the set current, it enters the constant current state, and the CC constant current indicator (red) lights up. The OUT indicator is the output status indicator, it is on when there is voltage at the output terminal, otherwise it is off; the CHAR indicator is the charging indicator, which is on when charging, and the FULL indicator is the full indicator. If the set constant current value is 2A, charging When the current reaches below 0.2A, turn the light, the FULL indicator is on, and the CHAR indicator is offInstructions:1. Use as an ordinary step-down module with overcurrent protection capability- Press the button to set the output voltage to the desired voltage value- Rotate the ADJ-I current adjustment potentiometer counterclockwise to the end, then measure the output short-circuit current with the 10A current range of the multimeter (connect the two test leads directly to the output terminal), and adjust the ADJ-I constant current potentiometer clockwise to make the output The current reaches the overcurrent protection value you want to set. (For example, the current value displayed by the multimeter is 2A, then the current can only reach 2A when the module is used, and the red constant current indicator light is on when the current reaches 2A, otherwise the indicator light is off) 2. Use as a battery charger- The module without constant current function cannot be used to charge the battery. Because the voltage difference between the exhausted battery and the charger is very large, the charging current is too large and the battery is damaged, so the battery should be used at the beginning. Constant current charging, when the charging reaches a certain level, it will automatically switch back to constant voltage charging- Determine the float voltage and charging current of the battery to be recharged; (if the lithium battery parameter is 3.7V/2200mAh, then the float voltage is 4.2V, and the charging current can reach 1C, that is, 2200mA)- Under no-load conditions, the output voltage of the button reaches the floating charge voltage; (if charging a 3.7V lithium battery, adjust the output voltage to 4.2V)- First turn the ADJ-I current adjustment potentiometer counterclockwise to the end, then measure the output short-circuit current with the 10A current range of the multimeter (just connect the two test leads to the output terminal directly), and adjust the ADJ-I constant current potentiometer clockwise to make the output The current reaches the predetermined charging current value- Connect the battery and charge (when setting: no battery is connected to the output terminal)3. Used as a high-power LED constant current driver module- Determine the operating current and operating voltage needed to drive the LED- Under no-load conditions, press the button to set the output voltage to reach the LED working voltage- First turn the ADJ-I current adjustment potentiometer counterclockwise to the end, then measure the output short-circuit current with the 10A current range of the multimeter (just connect the two test leads to the output terminal directly), and adjust the ADJ-I constant current potentiometer clockwise to make the output The current reaches the predetermined LED operating current- Connect the LED, test the machine (when setting: output no-load, do not connect the LED light) Precautions: 1. It is forbidden to short-circuit the input IN- of the module with the output OUT-, otherwise the constant current function will fail 2. Make sure that the power of the power supply is always greater than the power required by the output load. When the module is seriously hot, please reduce the power usage.Specification: Package Weight One Package Weight 0.07kgs / 0.16lb One Package Size 10cm * 10cm * 3cm / 3.94inch * 3.94inch * 1.18inch Qty per Carton 404 Carton Weight 30.00kgs / 66.14lb Carton Size 50cm * 50cm * 60cm / 19.69inch * 19.69inch * 23.62inch Loading Container 20GP: 177 cartons * 404 pcs = 71508 pcs40HQ: 412 cartons * 404 pcs = 166448 pcs

Leer Más Menos

Overview1. The SIM7600A-H 4G HAT is a 4G communication and GNSS positioning module, which supports LTE CAT4 up to 150Mbps for downlink data transfer. it is pretty low power consumption. 2. You can connect this 4G module with computer to surf the Internet, or attach it onto Raspberry Pi to enable functions like 4G high speed connection, wireless communication, making telephone call, sending SMS, global positioning, etc.Applicable Region1. SIM7600A-H is mainly applicable in North America (US, CA, MX), SIM7600E-H is mainly applicable in Southeast Asia, West Asia, Europe, Africa, SIM7600CE-T is mainly applicable in China. 2. Please check the supported bands according to your local service provider, select the proper one when placing order.Features1. Raspberry Pi connectivity, compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+ 2. Support dial-up, telephone call, SMS, MMS, mail, TCP, UDP, DTMF, HTTP, FTP, etc. 3. Support GPS, BeiDou, Glonass, LBS base station positioning 4. Onboard USB interface, to test AT Commands, get GPS positioning data, and so on 5. Onboard CP2102 USB to UART converter, for serial debugging 6. Breakout UART control pins, to connect with host boards like Arduino/STM32 7. SIM card slot, supports 1.8V/3V SIM card 8. Onboard audio jack and audio decoder for making telephone call 9. 2x LED indicators, easy to monitor the working status 10. Onboard voltage translator, operating voltage can be configured to 3.3V or 5V via jumper 11. Baudrate: 300bps-4Mbps (default: 115200bps) 12. Autobauding baudrate: 9600bps-115200bps 13. Control via AT commands (3GPP TS 27.007, 27.005, and V.25TER command set) 14. Support SIM application toolkit: SAT Class 3, USAT 15. Come with development resources and manual (examples for Raspberry Pi/Arduino/STM32)Communications Specifications1. Band: A. LTE: - SIM7600A-H: LTE-FDD B2/B4/B12 - SIM7600E-H: LTE-FDD B1/B3/B5/B7/B8/B20, LTE-TDD B38/B40/B41 - SIM7600CE-T: LTE-TDD B38/B39/B40/B41, LTE-FDD B1/B3/B8 B. WCDMA / TD-SCDMA/ CDMA 2000 - SIM7600A-H: UMTS/HSPA+ B2/B5 - SIM7600E-H: UMTS/HSPA+ B1/B5/B8 - SIM7600CE-T: UMTS/HSDPA/HSPA+ B1/B8, TD-SCDMA B34/B39, CDMA 1X/EVDO BC0 C. GSM/GPRS/EDGE 900/1800 MHz 2. Generation: 4G, 3G, 2.5G, 2G 3. Emitting power: 0.25W, 0.5W/EGSM900, 0.4W/DCS1800, 2W/GSM900, 1W/DCS1800 4. Data Speed - LTE CAT 4: Uplink=<50 Mbps, Downlink=<150 Mbps - UMTS: Uplink=<384Kbps, Downlink=<384Kbps - EDGE: Uplink=<236.8kbps, Downlink=<236.8kbps - GPRS: Uplink=<85.6kbps, Downlink=<85.6kbps - HSPA+: Uplink=<5.76Mbps, Downlink=<42MbpsGNSS Specifications1. Receiver type - 16-channel - C/A code 2. Sensitivity - Tracking: -159 dBm (GPS) / -158 dBm (GLONASS) / TBD (BD) - Cold starts: -148 dBm 3. Time-To-First-Fix (open air) - Cold starts: <35s - Hot starts: <1s 4. Accuracy - Position: <2.5m CEPSMS and Audio Specifications1. SMS - Support types: MT, MO, CB, Text, PDU - Storage: USIM card and ME (default) 2. Audio feature - Support echo cancellation - Support noise reductionOther Specifications1. Power supply: 5V 2. Operating voltage: 5V/3.3V (configured via jumper) 3. Operating temperature: -30 degree C ~ 80 degree C 4. Storage temperature: -45 degree C - 90 degree C 5. Dimension: 56.21mm x 65.15mmWhat is on Board1. SIM7600CE-T 2. CP2102 USB to UART converter 3. NAU8810 audio decoder 4. TXS0108EPWR voltage translator: Translates 3.3V/5V into 1.8V 5. MP2128DT power chip 6. MP1482 power chip 7. Raspberry Pi GPIO header: For connecting with Raspberry Pi 8. SIM7600 control interface: For connecting with host boards like Arduino/STM32 9. SIM card slot: Supports 1.8V/3V SIM card 10. TF card slot: Allows file/SMS/...storage 11. 3.5mm earphone/mic jack 12. USB interface: For testing AT Commands, getting GPS positioning data, etc. 13. USB to UART interface: For serial debugging, or login to Raspberry Pi 14. MAIN antenna connector 15. AUX antenna connector 16. GNSS antenna connector 17. Power switch 18. Network status indicator 19. Power indicator 20. Operating voltage selection jumper: - VCCIO-3.3V: set operating voltage as 3.3V - VCCIO-5V: set operating voltage as 5V 21. UART selection jumper: - A: Access Raspberry Pi via USB to UART - B: Control the SIM7600 by Raspberry Pi - C: Control the SIM7600 via USB to UARTPackage List1. SIM7600CE 4G HAT x1 2. LTE Antenna x1 3. GPS External Antenna (B) x1 4. USB type A plug to micro plug cable x2 5. RPi screws pack (2pcs) x1Specification: Package Weight One Package Weight 0.25kgs / 0.56lb One Package Size 15cm * 8cm * 3cm / 5.91inch * 3.15inch * 1.18inch Qty per Carton 260 Carton Weight 15.00kgs / 33.07lb Carton Size 60cm * 40cm * 39cm / 23.62inch * 15.75inch * 15.35inch Loading Container 20GP: 284 cartons * 260 pcs = 73840 pcs40HQ: 661 cartons * 260 pcs = 171860 pcs

Leer Más Menos

NVR1. Can connect IP camera, IP speed dome camera and DVS 2. High performance H.264 compression technology, processing and flexible 3. Plug and play (i8s Super agreement): One-click setting, IP address was assigned automatically 4. P2P cloud service, including cloud connecting, cloud monitoring, cloud transmitting to access IPC and NVR at any time and any place, Mobile viewing, support all smartphone systems 5. Support Onvif protocol, support High profile S, High profile G, compatible with different IP camera that based on Onvif, RTSP standard 6. Offer CMS for free 7. Compatible with main brand IP cameras: AXIS, SONY, Panasonic, SANYO, BOSCH, SAMSUNG, Honeywell, VIVOTEK, Ambarella, HIKVISION, DAHUA, Histream, Grandstream, TOPSEE, Launch, WISION, HYVISION, WAPA etc. 8. Embedded LINUX operating system 9. Image Code Control: Image code quality adjustable, variable bitstream and constant bitstream optional 10. Dual Stream: Each channel can set main stream and sub stream 11. Video Standard:1080P(1920*1080)30fps/960P/(1280*960)/720P(1280*720)30fps 12. Monitoring Image Quality:1080P(1920*1080) / 960P/(1280*960)/720P(1280*720) 13. Image Motion Detection: Each screen can set mutiple detection areas and set 6-level sensitivity (IPC Support) 14. Recording Playback Quality: Any 4ch playback simultaneously 15. Region cover: Every channel can set 4 cover regions, IPC support 16. Recording mode: Support manual, auto, dynamic detection, alarm trigger record mode(Partly needs IPC Support) 17. Support U disk, USB mobile HDD, USB DVD-RW network storage and backup 18. Video Input: - 4 x (1280*720) +sub(960*576)+4Ref.+4Play 4CH 1.0MP IP Camera - 4 x (1280*960)+sub(960*576)+1Ref.+4Play 4CH 1.3MP IP Camera - 4 x (1920*1080)+sub(960*576)+4Ref.+1Play 4CH 2.0MP IP Camera - 4 x (1920*1080)+sub(960*576)+4Ref.+1Play 1CH 1.0MP IP Camera - 4 x (720*576) +sub(352*288)+4Ref.+4Play 4CH D1 IP CameraIP Camera1. High performance H.264 compression technology, processing and flexible, high compression ratio 2. Support IR CUT dual OLP Switching, monitored day and night to achieve 3. Dual stream network transmission, for a variety of network environments 4. Support P2P mobile phone monitoring (compatible Iphone / Android) 5. Support Onvif 6. Motion detection, linkage videoSpecification: General Shape Bullet Power Supply DC 12V 1.0A Performance Motion detection, Night Vision Network Network Transmission P2P System / Hardware Mobile Access Android, iPhone OS, iPad Pixels 1.0MP Media Format Video Compression Format H.264 Night Vision Infrared Distance 30m NVR System Operating system: Embedded LINUX OS Image Code Control Image code quality adjustable, Variable bitstream and constant bitstream optional Dual Stream Support Recording Recording mode: Manual, auto, dynamic detection, alarm trigger Video interface Video output: 1ch VGA and 1ch HDMI Network RJ45 10M/100M self-adaptive LAN port USB Port USB*2, USB 2.0 for Mouse HDD SATA HDD (not included), Max 4TB Operation temperature -10 to 55 Degree Celsius Operation humidity 10-90 percent Power DC 12V 2.0A Physical Environment Environment Outdoor, Indoor Package Include Package Contents 4 x Cameras 1 x Mounting Accessories 1 x NVR 1 x CD 1 x User Manual 4 x Power Chargers 1 x Power Charger Package Weight One Package Weight 4.35kgs / 9.59lb One Package Size 37cm * 27cm * 21cm / 14.57inch * 10.63inch * 8.27inch Qty per Carton 4 Carton Weight 18.00kgs / 39.68lb Carton Size 56cm * 44cm * 38cm / 22.05inch * 17.32inch * 14.96inch Loading Container 20GP: 284 cartons * 4 pcs = 1136 pcs40HQ: 661 cartons * 4 pcs = 2644 pcs

Leer Más Menos

1. Product name: Xiaomi Router BE5000 2. Processor: Dual-core CPU 3. Memory: 512MB 4. 2.4G Wi-Fi: 2X2 (theoretical rate can reach 688Mbps) 5. 5G Wi-Fi: 3X3 160MHz (theoretical rate can reach 4323Mbps) 6. Product antenna: 5 high-gain WiFi antennas 7. Product heat dissipation: natural heat dissipation 8. Length, width and height: 271.9mm x 40.9mm x 220.8mm Complete machine interface: 1. 100/1000/2500M adaptive WAN/LAN port x 1 2. 10/100/1000M adaptive WAN/LAN port x 3 3. LED indicator x 1 4. System reset button x 1 5. Mesh button x 1 6. Power input interface x 1 Wireless parameters 1. Dual-band 2.4GHz and 5GHz 2. Wireless channels 2.4GHz Channel: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 3. 5GHz Channel: 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 Software parameters 1. Operating system: MiWiFi ROM 2. Wireless security: WPA-PSK/WPA2-PSK/WPA3-SAE encryption, 3. Wireless access control (black and white list), SSID hiding, anti-free network 4. Management application: Support Web, Mijia App (Android & iOS) Product accessories 1. Router x 1 2. Network cable x 1 3. US power adapter x 1Specification: Package Weight One Package Weight 0.73kgs / 1.61lb One Package Size 22cm * 21cm * 5cm / 8.66inch * 8.27inch * 1.97inch Qty per Carton 40 Carton Weight 26.60kgs / 58.64lb Carton Size 52cm * 46cm * 44cm / 20.47inch * 18.11inch * 17.32inch Loading Container 20GP: 253 cartons * 40 pcs = 10120 pcs40HQ: 588 cartons * 40 pcs = 23520 pcs

Leer Más Menos

Program1. Programming languages: EZPL, GEPL, GZPL, can be switched automatically 2. Random bundled software: - Label layout software: GoLabel (only supports EZPL) - Driver: Support Windows 2000, XP, Vista, 7, 8, Windows Server 2003 & 2008 - DLL: Support Windows 2000, XP and Vista 3. Built-in fonts: - Bitmap font: 6, 8, 10, 12, 14, 18, 24, 30, 16X26 and OCR A & B - Bitmap font printing direction can be rotated at an angle of 0 degree, 90 degree, 180 degree, 270 degree, the font can be individually rotated at an angle of 0 degree, 90 degree, 180 degree, 270 degree - Can be enlarged 8 times horizontally or vertically - Scalable fonts, with rotatable angles of 0 degree, 90 degree, 180 degree, 270 degree 4. Download fonts - Bitmap font can be downloaded, the printing direction can be rotated at 0 degree, 90 degree, 180 degree, 270 degree, the font can be individually rotated at 0 degree, 90 degree, 180 degree, 270 degree, and can enlarge 8 times horizontally or vertically - Downloadable Asian fonts, the printing direction can be rotated at 0 degree, 90 degree, 180 degree, 270 degree, and can be enlarged 8 times horizontally or vertically - Downloadable vector font (scalable font), the printing direction can be rotated at an angle of 0 degree, 90 degree, 180 degree, 270 degree 5. Barcode: - 1-D Bar codes: - Code 39, Code 93, EAN 8/13 (add on 2 & 5), UPC A / E (add on 2 & 5), I 2 of 5 & I 2 of 5 with Shipping Bearer Bars, Codabar, Code 128 (subset A, B, C), EAN 128, RPS 128, UCC 128, UCC / EAN-128 K-Mart, Random Weight, Post NET, ITF 14, China Postal Code, HIBC, MSI, Plessey, Telepen, FIM and GS1 DataBar - 2-D Bar codes: - PDF417, Datamatrix code, MaxiCode, QR code, Micro PDF417, Micro QR code and Aztec code 6. Code page: - CODEPAGE 437, 850, 851, 852, 855, 857, 860, 861, 862, 863, 865, 866, 869, 737 - WINDOWS 1250, 1251, 1252, 1253, 1254, 1255, 1257 - Unicode (UTF8, UTF16)Specifications1. Print mode: Thermal 2. Resolution: 203 dpi (8 dot / mm) 3. Print speed: 4 IPS (100 mm / sec) 4. Print width: 54mm (2.12 inches) 5. Print length: Min. 4 mm (0.16 inch); Max. 1727mm (68 inch) 6. Processor: 32 Bit RISC CPU 7. Memory: -4MB Flash (user available capacity is 2MB); 16MB -SDRAM 8. Sensor form: Reflective sensor: Removable; Translucent sensor: Center-mounted fixed type 9. Paper specifications: - Paper width: 15 mm (0.6 inches) ~ 60 mm (2.36 inches) - Paper thickness: 0.06 mm (0.003 inch) ~ 0.20 mm (0.008 inch) - Paper roll outer diameter: Maximum diameter 127 mm (5 inches) - Paper roll core: 25.4 mm (1 inch) / 38.1 mm (1.5 inch) 10. Graphics processing: Monochrome PCX and BMP are supported by default, other image file types can be supported by software control 11. Transmission interface: - USB Device (B-Type) - Serial port: RS-232 (DB-9) - IEEE 802.3 10 / 100Base-Tx Ethernet port (RJ-45) 12. Control panel: -A set of three-color LED indicators: Power (red, orange, green lights) -A set of multi-function hardware control keys: FEED 13. Timing device: Standard 14. Power supply: 100-240VAC, 50-60Hz (AC / DC automatic conversion power supply) 15. Working environment: - Operating temperature: 41 degree F to 104 degree F (5 degree C to 40 degree C) - Storage temperature: -4 degree F to 122 degree F (-20 degree C to 50 degree C) - Humidity Operating humidity: 30-85%, non-condensing. - Storage humidity: 10-90%, non-condensing. 16. Safety regulations: CE (EMC), FCC Class A, CB, cUL, CCC 17. Body size: Length: 218 mm (8.58 inches), Height: 172 mm (6.77 inches), Width: 100 mm (3.94 inches) 18. Body weight: The body does not contain other consumables or the optional equipment weighs 1.2 kg (2.65lb)Specification: Package Weight One Package Weight 2.07kgs / 4.56lb One Package Size 24cm * 20cm * 20cm / 9.45inch * 7.87inch * 7.87inch Qty per Carton 8 Carton Weight 16.50kgs / 36.38lb Carton Size 50cm * 42cm * 42cm / 19.69inch * 16.54inch * 16.54inch Loading Container 20GP: 302 cartons * 8 pcs = 2416 pcs40HQ: 701 cartons * 8 pcs = 5608 pcs

Leer Más Menos