Productos
-
MC-03 130dB Multi-function Door and Window Anti-theft Alarm with 5 Modes
1. Material: ABS2. Battery: LR44X3 (included)3. Host size: 65x34x16.5 mm4. Weight: 42g5. Remote control size: 36x10x14 mm6. Sensing range: 8-15 mm7. Standby time: about 1 year8. Standby current: less than or equal to 6uAh9. According to the triangle mounting marks of door sensor and magnetic stripe, it can be installed in left and right adjustment positions10. 5 modes of alarm/doorbell(alarm 30 seconds mode, doorbell mode, alarm mode, beep mode and delayed alarm mode), can be installed in both directions, 130dB super loud alarm sound12. Working principle: when the door is opened, the door magnet and the magnetic strip are separated and the 8-15 mm alarm sounds and closes to stop the alarmSpecification: Package Weight One Package Weight 0.06kgs / 0.14lb One Package Size 10cm * 5cm * 5cm / 3.94inch * 1.97inch * 1.97inch Qty per Carton 468 Carton Weight 30.00kgs / 66.14lb Carton Size 50cm * 50cm * 60cm / 19.69inch * 19.69inch * 23.62inch Loading Container 20GP: 177 cartons * 468 pcs = 82836 pcs40HQ: 412 cartons * 468 pcs = 192816 pcs
£2.99
-
MD31 Mini 1080P HD Camcorder Night Vision PIR Motion Action Micro Camera, MD31
1. Video resolution: 1920x10802. Recording time: about 11 hours3. Standby time: about 40days4. Charging time: about 5 hours5. Battery capacity: about 1500mah6. Supported memory: TF card 8GB-128GB (not shipped)7. Frame rate: about 30fps7. Interface type: USB8. Support loop recording/PIR9. Charging voltage: DC5V 1A10. Viewing angle: 120 degrees11. Video format: AVISpecification: General Model MD31 Performance Night Vision, Loop recording Memory up to 128GB (not included) Interface Micro USB Power Input DC5V 1A View Angle 120 degrees Media Format Video Compression Format AVI Frame Rate (FPS) 30fps Battery Capacity 1500mah Charging Time 5h Work Time 11h Standby Time 40days Package Weight One Package Weight 0.18kgs / 0.40lb One Package Size 14cm * 11cm * 5cm / 5.51inch * 4.33inch * 1.97inch Qty per Carton 100 Carton Weight 17.00kgs / 37.48lb Carton Size 52cm * 42cm * 32cm / 20.47inch * 16.54inch * 12.6inch Loading Container 20GP: 381 cartons * 100 pcs = 38100 pcs40HQ: 885 cartons * 100 pcs = 88500 pcs
£15.99
-
MD80 3 in 1 Mini Digital VIDEO Camera Camcorder POCKET DV with 720*480 pixels, Viewing Angle: 60 Degree, MD80
About the product1. The Mini DV/DVR MD80 is mini digital video camera, smaller than a lighter, and just about as cheap! 2. It is very fashionable and wearable and matches all kinds of portable tools, making it a good little cam unit. 3. It records 720X480 video in AVI format at 30 frames per second this camcorder keeps away blur and distortions. 4. It can be set to stand-by for up to 250 hours until it is activated by a sound. 5. You can set it up in a room on audio-activated standby mode, where it will happily sit for nearly two weeks on a single battery charge, waiting for a noise to start it recording. It uses micro SD Card, which means you can store up to 32GB of footage on it, Powered by the Li-battery, and it plugs into your computer via USB (which also charges it). 6. The MD80 video camera captures videos with impeccable clarity and acute details. This video camera, with 60 degree view angle, lets you capture landscape videos on a wider angle. 7. With an extensive memory support, this camcorder offers ample of storage space. 8. The thumb size manual alloy housing of this video camera offers reliability and longevity.Features1. Mini DV Video Camera DVR Recorder Camcorder with Lithium Battery 2. New and high quality 3. Small size,easy to carry 4. Alloyed shell,much harder 5. Support sound control video recording 6. Support USB charging 7. Support Micro SD card (TF card)Specification: General Programs Generalplus Pixel 1.3M View Angle 70 Degree Memory medium Micro SD Card (TF Card) Battery Capacity 230mAh Consumption Current 3.7V / 120mA (Max) Interface USB 2.0 Operation System Windows 98, Mac OS10.4 Formats Video Format AVI Video Coding Motion JPEG Physical Environment Minimum Illumination 1Lux(Min) Store Temperature -20 Celsius Degree to 80 Celsius Degree Operation Temperature -10 Celsius Degree to 50 Celsius Degree Operation Humidity 15 - 85% RH Package Include Package Contents 1 x Mini DV 2 x Brackets 1 x Clip-On Adapter 1 x USB Cable 1 x Silicone Case 1 x User Manual 1 x CD Driver Package Weight One Package Weight 0.09kgs / 0.20lb Qty per Carton 100 Carton Weight 11.00kgs / 24.25lb Carton Size 50cm * 35cm * 30cm / 19.69inch * 13.78inch * 11.81inch Loading Container 20GP: 507 cartons * 100 pcs = 50700 pcs40HQ: 1179 cartons * 100 pcs = 117900 pcs
£3.99
-
Soporte de montaje de metal para cámara CCTV CCD, 2
1. Diseño robusto 2. Material: metal 3. Articulación esférica para un fácil ajuste del ángulo. 4. El soporte es un montaje de metal resistente para usar con cámaras de seguridad de cuerpo completo. 5. Este soporte se instala en una pared o techo y permite un fácil ajuste de inclinación. 6. Inclinación ajustable 7. El soporte de carcasa de metal es ideal para cámaras CCTV CCD 8. Aplicaciones interiores y exteriores 9. Diámetro del chasis: 4,6 cm 10. Altura: 6,5 cm Especificación: Peso del paquete Peso de un paquete 0,07 kg/0,14 lb Un tamaño de paquete 6 cm * 6 cm * 6 cm / 2,36 pulgadas * 2,36 pulgadas * 2,36 pulgadas Cantidad por caja 200 Peso de la caja 16,60 kg/36,60 lb Tamaño de la caja 42 cm * 30 cm * 30 cm / 16,54 pulgadas * 11,81 pulgadas * 11,81 pulgadas Contenedor de carga 20GP: 705 cajas * 200 piezas = 141000 piezas 40HQ: 1637 cajas * 200 piezas = 327400 piezas
£2.99 £0.99
-
Metal Waterproof Fingerprint Swipe Password Access Control Multifunction All-in-one Machine
1. Size: 13.9 x 5.6 x 2cm2. Storage capacity: 100 households3. Working voltage: DC 12V4. Alarm output: ≤20A5. Working environment: -40 ～ 60 Degrees Celsius6. Card reading distance: 3-6cm7. Management card: support adding card and deleting card8. Door opening method: support card plus password, multi-card door opening method9. Ideal for office, office building, factory staff dormitory, building public passage, home gate controlSpecification: Package Weight One Package Weight 0.61kgs / 1.34lb One Package Size 16cm * 8cm * 4cm / 6.3inch * 3.15inch * 1.57inch Qty per Carton 50 Carton Weight 30.00kgs / 66.14lb Carton Size 58cm * 29cm * 14cm / 22.83inch * 11.42inch * 5.51inch Loading Container 20GP: 1132 cartons * 50 pcs = 56600 pcs40HQ: 2628 cartons * 50 pcs = 131400 pcs
£49.99
-
Mini NVR Full HD 8-Channel CCTV Security NVR 1080P ONVIF Network Video Recorder for IP Camera
Network Interface:RJ45 10/100MVideo Input Interface:RJ45Wireless Security:WEPNetwork Protocol:SMTP,PPPoE,HTTP,FTP,DHCPSupported Operating Systems:Microsoft Windows 7,Microsoft Windows XPAudio Compression Format:G711AAudio Input:NoIP Mode:Static IP address,Dynamic IP addressBackup Type:Hard Drive,USB Flash DiversAudio Output:NoneTechnology:NetworkAlarm Action:FTP PhotoVideo Resolution:1080PSupported Mobile Systems:for iPhone OS,AndroidHard drive Interface Type:SATAVideo Output:1VGA + 1HDMIe-Cloud(P2P):YesTwo-way Audio:NoPOE:NoneCompression Format:H.264Video Standard:NTSC,PALResolution:Full HD1080PONVIF:Yes ( ONVIF 2.0 )Input For 8Channel NVR:8*1080P/12*960PPlayback:2*1080P/4*960 For 4CH ; 2*1080P/4*960P/4*720P For 8CHOutput:1*1080P HDMI /1*VGADimention:21cm(L)*20cm(W)*4cm(H)Features :1.H.264 High profile compression algorithm ideal for standalone NVR2.Realtime live display up to 4/8 cameras3.Pentaplex function:live,recording,playback,backup & remote access;4.Support Dual-streams,to make mobile monitoring very easy,flexible for network transmission5.Smart video detection:motion detection,video blind,video loss6.Smart camera settings:privacy masking,camera lock,color setting,and tittle display7.Easy backup methods: USB devices,remote network and client software backup8.Alarm triggering screen tips,buzzer,PTZ preset,e-mail &FTP upload9.Smart HDDs Management:non-working HDD hibernationg,HDD faulty alarm,Raid function10.Powerful network software:built-in web server,multi-DVR client &SMS Networking access for remote live viewing,recording,playback,setting,system statu,event log,e-mail & ftp function11.Support DHCP / PPPOE / FTP / DNS / DDNS / NTP / Email alarm / IP right management / IP search / network alarm center functions, support web client, standalone client and SDK.12.With the sound system for the protection circuit, unique triple watchdog function, very low power consumption, to ensure the equipment never be hang up. With the unique black box technology, can monitor the whole run process of the equipment, can greatly reduce the maintenance costs.13.Enable strong multi-way synchronization with max 1/4 channel playback, realize the zero-delay between playback channels14. Support Standard Onvif 2.0 protocal15.Real P2P : Cloud : XMEYE.NET ; APP :XMEYEPackage Included:4CH/8CH NVR x 1 Mouse x 1 Power Supply for NVR x 1Users Manual x 1Specification: Package Weight One Package Weight 1.20kgs / 2.65lb One Package Size 28cm * 26cm * 10cm / 11.02inch * 10.24inch * 3.94inch Qty per Carton 20 Carton Weight 15.00kgs / 33.07lb Carton Size 30cm * 50cm * 50cm / 11.81inch * 19.69inch * 19.69inch Loading Container 20GP: 355 cartons * 20 pcs = 7100 pcs40HQ: 825 cartons * 20 pcs = 16500 pcs
£24.99
-
Mini PIR Alert Sensor Wireless Infrared GSM Alarm Monitor Motion Detector Detection Home Anti-theft System, EU Plug, Infrared GSM Alarm
Description:1. Switch on: Open the card holder cover, insert the SIM card into the card holder according to the instructions and it will automatically power on. When power on, the indicator light is on for 3 seconds. After the indicator light is off, close the cover. The alarm cat will enter the monitoring and sensing state about one minute after the machine is turned on. Information to the bound number2. Number setting: 5 seconds after dialing the connection with a communication tool such as a mobile phone, the machine will automatically connect to hear the call voice, and the operation is very simple.3. When the products range senses that the human body is passing back and forth, the product will call the bound number, and the sensor head will enter the function sensing state after one minute of power-on, and the sensing trigger will flash LED4. Charging indicator changes: When the host is charging, the charger light is red, and when it is fully charged, the light will turn yellow.5. Working frequency: 850MHZ, 900MHZ, 1800MHZ, 1900MHZStandby time: 5-7 days standby with human induction, 15-20 days standby without inductionFunction introduction and use method:1. When the human body approaches the alarm cat, it will automatically detect the human body signal and turn on the automatic dialing2. High sensitivity within 4 meters3. Wireless is easy to install and can be used indoors, finance room, master room, childrens room, warehouse, hospital, etc. wherever security is needed4. Designed with wireless communication technology, low power consumption, long standby time, accurate alarm, no false alarms, no random reports5. When installing, place or paste the alarm cat at a certain height, aim at the place where the human body walks, and the distance is within 4 meters from the human body. The alarm cat can sense the human bodys walking within 120 ° of the left and right angle range. Or the animals are shaking back and forth, the alarm cat will be activated in a very short timeUse:1. Put it in the family living room, bedroom, etc .: With him, he goes out to work and travels. When a stranger comes in, he reports the alarm to the owner as soon as possible.2. It can be placed outside the door of important places, not limited by distance. It can be placed in a location that requires a certain distance without being disturbed. It can be informed in advance that someone comes in;3. Place the elderly, the patients room, the elderly during the time out, the patients behavior will immediately report to the family or medical staff;4. Placed in the corner of the car or high up in the warehouse, he can protect your precious beloved car or warehouses valuables for you. After getting abnormal conditions, the thief can be caught without any knowledge;5. Home nurse: When the elderly or other loved ones live alone, are at home or are sick or even paralyzed in bed all year round, you can stay with your loved ones remotely. Even if you have a babysitter or a caregiver, you can monitor yourself for any abnormalities at any time, which will be even more reassuring.6. Medical care: Family members are hospitalized, and they want to know the situation of their loved ones at any time. Some family members are thousands of kilometers away from the hospital and have many inconveniences. Effectively solved this problem. The installation of such equipment in hospitals is a new high-tech means to improve the quality of their services.7. The facilities of base stations, iron towers or power systems are located in unmanned areas in high mountains. Such equipment is not only extremely expensive, but also causes communications or electricity after the incident.8. Applicable to the bank security car, you can always check and understand the security of the currency transport car. Force interruption, indirect loss cannot be estimated, the alarm cat solves the difficulties of field network cables, no telephone lines, and inability to reach in real time, and truly audible, an anti-theft integrated system that makes illegal thieves scared and frightenedSpecification: Package Weight One Package Weight 0.14kgs / 0.31lb One Package Size 15cm * 13cm * 5cm / 5.91inch * 5.12inch * 1.97inch Qty per Carton 194 Carton Weight 30.00kgs / 66.14lb Carton Size 50cm * 50cm * 60cm / 19.69inch * 19.69inch * 23.62inch Loading Container 20GP: 177 cartons * 194 pcs = 34338 pcs40HQ: 412 cartons * 194 pcs = 79928 pcs
£10.99
-
Mira Sales Mini Pocket EDC Stainless Steel Multi-function Self Security Defense Personal Tactical Tool
Material:stainless steelWeight:36gSize:90x60x3.8mm (L*W*H)Features: 1. Sophisticated processing technology 2. Combining several functions in one (interior angle wrench, bottle opener, screwdriver, hand stab) 3. Compact size and easy to carry 4. Processing: peripheral whole stamping twice, drilling polishing mill - stone wash. Inner circumference / hex portion of all vertical CNC wire cutting process 5. Application: multi-size interior angle wrench / screwdriver / bottle opener / screwdriver/self defenseSpecification: Package Weight One Package Weight 0.06kgs / 0.14lb One Package Size 11cm * 7cm * 5cm / 4.33inch * 2.76inch * 1.97inch Qty per Carton 240 Carton Weight 15.00kgs / 33.07lb Carton Size 30cm * 50cm * 50cm / 11.81inch * 19.69inch * 19.69inch Loading Container 20GP: 355 cartons * 240 pcs = 85200 pcs40HQ: 825 cartons * 240 pcs = 198000 pcs
£2.99 £0.99
-
Mini Wired Alarm PSTN / GSM Wireless Home Alarm Security System 120 Decibel Horn Alarm Accessories
Feature:1. Sound pressure / decibel: 120 (At Rated Voltage at 1M)2. Maximum current: 180mA3. Working temperature: -20 ~ 60 ° C4. Impedance: 6/8/12 Ohm5. Voice coil diameter: Φ18.3mm6. Rated voltage: 12VDC/24VDC--Only 15W7. Working voltage range: 9~16VDC/20~25VDC8. Power: 15W/20W/25W9. Sound pressure / decibel: 105/108/110 (At Rated Voltage at 1M)10. Maximum current: 700/1000/1200mA11. Audio: Warble/1-Tone /6-Tone12. Working temperature: -20 ~ 60 ° CSpecification: Package Weight One Package Weight 0.07kgs / 0.16lb One Package Size 5.5cm * 5.5cm * 4.9cm / 2.17inch * 2.17inch * 1.93inch Qty per Carton 210 Carton Weight 15.00kgs / 33.07lb Carton Size 32cm * 32cm * 29cm / 12.6inch * 12.6inch * 11.42inch Loading Container 20GP: 897 cartons * 210 pcs = 188370 pcs40HQ: 2084 cartons * 210 pcs = 437640 pcs
£2.99 £1.99
-
Mini Wired Red Strobe Siren for Burglar Security Alarm, Mini
1. Sound with red strobe light 2. Compatible with any burglar alarms Product Specifications: 1. Alarm loudness volume: More than 110dB /30cm 2. Flash/ min: 150 times 3. Rated Current: Less than 300 mA 4. Power supply: DC12V 5. Size: 120mm x 70mm x 45mm Operation: Plug the wired siren to siren socket of the main unit. When the main unit triggers the alarm, the siren starts upSpecification: Package Weight One Package Weight 0.12kgs / 0.27lb One Package Size 13.5cm * 8.5cm * 5cm / 5.31inch * 3.35inch * 1.97inch Qty per Carton 72 Carton Weight 10.50kgs / 23.15lb Carton Size 50cm * 35cm * 35cm / 19.69inch * 13.78inch * 13.78inch Loading Container 20GP: 435 cartons * 72 pcs = 31320 pcs40HQ: 1010 cartons * 72 pcs = 72720 pcs
£2.99 £1.99
-
ML18 Mini Ultra Wide Angle Smart Video Doorbell Support Two-way Voice, ML18
1. Battery: 1000MA 2. Viewing angle: 60 degrees 3. Recording method: wake-up recording 4. Resolution: 640x480 5. Support two-way voice intercom, cloud storage. 6. Wake-up method: ring the bell to wake up 7. Supports wireless WiFi connection, does not support 4G/5G 8. Support system: Android/iOS 9. 90 degree wide angle, support 5m night vision. 10. Press the doorbell to automatically store in the cloud, and you can view past pictures at any time. 11. Real-time video calls, easy to deal with visitors. 12. Built-in 1000mAh large-capacity battery, super battery life. 13. Support switching multiple modes of voice changing function. 14. The memory card can be inserted, and the maximum support is 128G memory card. Press the doorbell to start recording.(This product does not contain a memory card) 15. Use with Ding Dong to prevent missed listening. 16. Convenient installation, can be pasted and punched, simple and convenient. Specification: Package Weight One Package Weight 0.20kgs / 0.45lb One Package Size 12cm * 10cm * 5cm / 4.72inch * 3.94inch * 1.97inch Qty per Carton 120 Carton Weight 25.00kgs / 55.12lb Carton Size 50cm * 32cm * 52cm / 19.69inch * 12.6inch * 20.47inch Loading Container 20GP: 320 cartons * 120 pcs = 38400 pcs40HQ: 744 cartons * 120 pcs = 89280 pcs
£10.99
-
ML19 90 Degree Wide Angle Wireless Smart Video Doorbell, ML19
1. Viewing angle: 60 degrees2. Network frequency range: 2.4GHZ-2.4835GHZ3. Recording method: wake-up recording4. APP operating system: for iOS/Android5. Battery: Built-in 1000MA6. Wake-up method: ring the bell to wake up7. Infrared lighting: 6pcs 940 infrared lights8. Resolution: 640x4809. Support playback, two-way voice intercom, cloud storage.10. Press the doorbell to automatically store in the cloud, and you can view past pictures at any time.11. Real-time video calls, easy to deal with visitors.12. Built-in 1000mAh large-capacity battery, super battery life.13. Support switching multiple modes of voice changing function.14. The memory card can be inserted, and the maximum support is 128G memory card. Press the doorbell to start recording.15. Use with Ding Dong to prevent missed listening.16. Convenient installation, can be pasted and punched, simple and convenient.Specification: Package Weight One Package Weight 0.20kgs / 0.45lb One Package Size 12cm * 10cm * 5cm / 4.72inch * 3.94inch * 1.97inch Qty per Carton 120 Carton Weight 25.00kgs / 55.12lb Carton Size 50cm * 32cm * 52cm / 19.69inch * 12.6inch * 20.47inch Loading Container 20GP: 320 cartons * 120 pcs = 38400 pcs40HQ: 744 cartons * 120 pcs = 89280 pcs
£8.99
-
Mobile LED 3G WCDMA 2100MHz Signal Booster / Signal Repeater with Sucker Antenna, Signal Repeater
About Signal BoosterCell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save a life. Unfortunately, there are still some places where one can find themselves - out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: parking lots, tunnels, big stores, office buildings, cars, boats, house in remote areas, etc. Here we will bring you a new kind of LED 3G signal booster. Welcome to buy!Features1. High-gain linear power amplifier. 2. ALC and AGC function technology. 3. Ultra-low noise receive amplifier. 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters. 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications. 7. With full-duplex communication mode. 8. It explores an effective and reasonable method to dispel the heat.Installation Steps1. Use your mobile phone to test signal strength outside house or on roof, -70dBm is the basic requirement (full bar). 2. Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Mount your indoor antenna with signal repeater. 5. Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Notices1. Connect outdoor (BTS) port with outdoor antenna. Connect indoor ANT (MS) port with indoor antenna. Outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away at least from each other. 2. Indoor and outdoor antennas must be separated by wall. 3. If the signal is still weak after installation, please check whether or not the outdoor antenna is pointed to signal tower correctly or elsewhere with stronger signal and confirm that the signal strength achieved -70dBm. 4. If no signal for a long time after installation, please check the device power adapter whether or not connected perfectly and connectors connect well. 5. If strength is not steady, please check if outdoor and indoor antennas are too close. Please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 6. Packed the outdoor connector by waterproof glue, otherwise wet condition will reduce the signal cover area.Specification: General Frequency Range WCDMA 2100MHz, Uplink 1920-1980MHz, Downlink 2110-2170MHz Gain Uplink 63-67dB, Downlink 63-67dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC:100~240V, 50/60Hz; DC:12V 2A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 198 x 182 x 20mm Weight 1200g Package Include Package Contents 1 x 5dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 1.65kgs / 3.64lb One Package Size 31cm * 23cm * 11cm / 12.2inch * 9.06inch * 4.33inch Qty per Carton 4 Carton Weight 7.40kgs / 16.31lb Carton Size 48cm * 33cm * 24cm / 18.9inch * 12.99inch * 9.45inch Loading Container 20GP: 701 cartons * 4 pcs = 2804 pcs40HQ: 1628 cartons * 4 pcs = 6512 pcs
£48.99
-
Mobile LED DCS 1800MHz Signal Booster / Signal Repeater with Sucker Antenna, Signal Booster Gold
About Signal BoosterCell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save a life. Unfortunately, there are still some places where one can find themselves - out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: parking lots, tunnels, big stores, office buildings, cars, boats, house in remote areas, etc. Here we will bring you a new kind of LED DCS signal booster. Welcome to buy!Features1. High-gain linear power amplifier. 2. ALC and AGC function technology. 3. Ultra-low noise receive amplifier. 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters. 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications. 7. With full-duplex communication mode. 8. It explores an effective and reasonable method to dispel the heat.Installation Steps1. Use your mobile phone to test signal strength outside house or on roof, -70dBm is the basic requirement (full bar). 2. Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Mount your indoor antenna with signal repeater. 5. Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Notices1. Connect outdoor (BTS) port with outdoor antenna. Connect indoor ANT (MS) port with indoor antenna. Outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away at least from each other. 2. Indoor and outdoor antennas must be separated by wall. 3. If the signal is still weak after installation, please check whether or not the outdoor antenna is pointed to signal tower correctly or elsewhere with stronger signal and confirm that the signal strength achieved -70dBm. 4. If no signal for a long time after installation, please check the device power adapter whether or not connected perfectly and connectors connect well. 5. If strength is not steady, please check if outdoor and indoor antennas are too close. Please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 6. Packed the outdoor connector by waterproof glue, otherwise wet condition will reduce the signal cover area.Specification: General Frequency Range DCS 1800MHz, Uplink 1710-1785MHz, Downlink 1805-1880MHz Gain Uplink 63-67dB, Downlink 63-67dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC:100~240V, 50/60Hz; DC:12V 2A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 198 x 182 x 20mm Weight 1200g Package Include Package Contents 1 x 5dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 1.58kgs / 3.48lb One Package Size 31cm * 23cm * 11cm / 12.2inch * 9.06inch * 4.33inch Qty per Carton 4 Carton Weight 7.40kgs / 16.31lb Carton Size 48cm * 33cm * 24cm / 18.9inch * 12.99inch * 9.45inch Loading Container 20GP: 701 cartons * 4 pcs = 2804 pcs40HQ: 1628 cartons * 4 pcs = 6512 pcs
£48.99
-
Mobile LED DCS 1800MHz Signal Booster / Signal Repeater with Yagi Antenna, LED Booster
About Signal BoosterCell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save a life. Unfortunately, there are still some places where one can find themselves - out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: parking lots, tunnels, big stores, office buildings, cars, boats, house in remote areas, etc. Here we will bring you a new kind of LED DCS signal booster. Welcome to buy!Features1. High-gain linear power amplifier. 2. ALC and AGC function technology. 3. Ultra-low noise receive amplifier. 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters. 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications. 7. With full-duplex communication mode. 8. It explores an effective and reasonable method to dispel the heat.Installation Steps1. Use your mobile phone to test signal strength outside house or on roof, -70dBm is the basic requirement (full bar). 2. Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Mount your indoor antenna with signal repeater. 5. Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Notices1. Connect outdoor (BTS) port with outdoor antenna. Connect indoor ANT (MS) port with indoor antenna. Outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away at least from each other. 2. Indoor and outdoor antennas must be separated by wall. 3. If the signal is still weak after installation, please check whether or not the outdoor antenna is pointed to signal tower correctly or elsewhere with stronger signal and confirm that the signal strength achieved -70dBm. 4. If no signal for a long time after installation, please check the device power adapter whether or not connected perfectly and connectors connect well. 5. If strength is not steady, please check if outdoor and indoor antennas are too close. Please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 6. Packed the outdoor connector by waterproof glue, otherwise wet condition will reduce the signal cover area.Specification: General Frequency Range DCS 1800MHz, Uplink 1710-1785MHz, Downlink 1805-1880MHz Gain Uplink 63-67dB, Downlink 63-67dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC:100~240V, 50/60Hz; DC:12V 2A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 198 x 182 x 20mm Weight 1200g Package Include Package Contents 1 x 12dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 5m RG6-50 OHM Indoor Coaxial Cable 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 2.78kgs / 6.13lb One Package Size 51cm * 23cm * 15cm / 20.08inch * 9.06inch * 5.91inch Qty per Carton 2 Carton Weight 5.60kgs / 12.35lb Carton Size 53cm * 25cm * 32cm / 20.87inch * 9.84inch * 12.6inch Loading Container 20GP: 628 cartons * 2 pcs = 1256 pcs40HQ: 1460 cartons * 2 pcs = 2920 pcs
£52.99
-
Mobile LED GSM 980MHz Signal Booster / Signal Repeater with Sucker Antenna, LED GSM980
About Signal BoosterCell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save a life. Unfortunately, there are still some places where one can find themselves - out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: parking lots, tunnels, big stores, office buildings, cars, boats, house in remote areas, etc. Here we will bring you a new kind of LED signal booster. Welcome to buy!Features1. High-gain linear power amplifier. 2. ALC and AGC function technology. 3. Ultra-low noise receive amplifier. 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters. 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications. 7. With full-duplex communication mode. 8. It explores an effective and reasonable method to dispel the heat.Installation Steps1. Use your mobile phone to test signal strength outside house or on roof, -70dBm is the basic requirement (full bar). 2. Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Mount your indoor antenna with signal repeater. 5. Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Notices1. Connect outdoor (BTS) port with outdoor antenna. Connect indoor ANT (MS) port with indoor antenna. Outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away at least from each other. 2. Indoor and outdoor antennas must be separated by wall. 3. If the signal is still weak after installation, please check whether or not the outdoor antenna is pointed to signal tower correctly or elsewhere with stronger signal and confirm that the signal strength achieved -70dBm. 4. If no signal for a long time after installation, please check the device power adapter whether or not connected perfectly and connectors connect well. 5. If strength is not steady, please check if outdoor and indoor antennas are too close. Please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 6. Packed the outdoor connector by waterproof glue, otherwise wet condition will reduce the signal cover area.Specification: General Frequency Range GSM 900MHz, Uplink 890-915MHz, Downlink 935-960MHz Gain Uplink 63-67dB, Downlink 63-67dB Output Power Uplink 15-19dBm, Downlink 15-19dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC:100~240V, 50/60Hz; DC:12V 2A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 198 x 186 x 20mm Weight 1200g Package Include Package Contents 1 x 5dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 1.39kgs / 3.07lb One Package Size 31cm * 20cm * 11cm / 12.2inch * 7.87inch * 4.33inch Qty per Carton 4 Carton Weight 7.40kgs / 16.31lb Carton Size 42cm * 33cm * 24cm / 16.54inch * 12.99inch * 9.45inch Loading Container 20GP: 801 cartons * 4 pcs = 3204 pcs40HQ: 1861 cartons * 4 pcs = 7444 pcs
£32.99
-
Mobile LED GSM 980MHz Signal Booster / Signal Repeater with Yagi Antenna, LED GSM Antenna
About Signal BoosterCell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save a life. Unfortunately, there are still some places where one can find themselves - out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: parking lots, tunnels, big stores, office buildings, cars, boats, house in remote areas, etc. Here we will bring you a new kind of LED signal booster. Welcome to buy!Features1. High-gain linear power amplifier. 2. ALC and AGC function technology. 3. Ultra-low noise receive amplifier. 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters. 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications. 7. With full-duplex communication mode. 8. It explores an effective and reasonable method to dispel the heat.Installation Steps1. Use your mobile phone to test signal strength outside house or on roof, -70dBm is the basic requirement (full bar). 2. Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Mount your indoor antenna with signal repeater. 5. Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Notices1. Connect outdoor (BTS) port with outdoor antenna. Connect indoor ANT (MS) port with indoor antenna. Outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away at least from each other. 2. Indoor and outdoor antennas must be separated by wall. 3. If the signal is still weak after installation, please check whether or not the outdoor antenna is pointed to signal tower correctly or elsewhere with stronger signal and confirm that the signal strength achieved -70dBm. 4. If no signal for a long time after installation, please check the device power adapter whether or not connected perfectly and connectors connect well. 5. If strength is not steady, please check if outdoor and indoor antennas are too close. Please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 6. Packed the outdoor connector by waterproof glue, otherwise wet condition will reduce the signal cover area.Specification: General Frequency Range GSM 900MHz, Uplink 890-915MHz, Downlink 935-960MHz Gain Uplink 63-67dB, Downlink 63-67dB Output Power Uplink 15-19dBm, Downlink 15-19dBm Bandwidth 60m Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <3 MTBF >50000h Power Supply AC:100~240V, 50/60Hz; DC:12V 2A Power Consumption <5W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 198 x 186 x 20mm Weight 1200g Package Include Package Contents 1 x 12dB Outdoor Antenna 1 x 3dB Indoor Antenna 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 2.36kgs / 5.21lb One Package Size 52cm * 26cm * 15cm / 20.47inch * 10.24inch * 5.91inch Qty per Carton 2 Carton Weight 5.60kgs / 12.35lb Carton Size 54cm * 28cm * 32cm / 21.26inch * 11.02inch * 12.6inch Loading Container 20GP: 551 cartons * 2 pcs = 1102 pcs40HQ: 1279 cartons * 2 pcs = 2558 pcs
£34.99
-
Mobile LED WCDMA 2100MHz & GSM 900MHz Signal Booster / Signal Repeater with Logarithm Periodic Antenna
About Signal BoosterCell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save a life. Unfortunately, there are still some places where one can find themselves - out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: parking lots, tunnels, big stores, office buildings, cars, boats, house in remote areas, etc. Here we will bring you a new kind of LED signal booster. Welcome to buy!Features1. High-gain linear power amplifier. 2. ALC and AGC function technology. 3. Ultra-low noise receive amplifier. 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters. 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications. 7. With full-duplex communication mode. 8. It explores an effective and reasonable method to dispel the heat.Installation Steps1. Use your mobile phone to test signal strength outside house or on roof, -70dBm is the basic requirement (full bar). 2. Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Mount your indoor antenna with signal repeater. 5. Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Notices1. Connect outdoor (BTS) port with outdoor antenna. Connect indoor ANT (MS) port with indoor antenna. Outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away at least from each other. 2. Indoor and outdoor antennas must be separated by wall. 3. If the signal is still weak after installation, please check whether or not the outdoor antenna is pointed to signal tower correctly or elsewhere with stronger signal and confirm that the signal strength achieved -70dBm. 4. If no signal for a long time after installation, please check the device power adapter whether or not connected perfectly and connectors connect well. 5. If strength is not steady, please check if outdoor and indoor antennas are too close. Please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 6. Packed the outdoor connector by waterproof glue, otherwise wet condition will reduce the signal cover area.Specification: General Frequency Range WCDMA 2100MHz, Uplink 1920-1980MHz, Downlink 2110-2170MHz, GSM 900MHz, Uplink 890-915MHz, Downlink 935-960MHz Gain 65dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Automatic Gain Control >20dB Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <2 MTBF >50000h Power Supply AC:90~265V, 50/60Hz; DC:12V 2A Power Consumption <20W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 198 x 182 x 20mm Weight 1200g Package Include Package Contents 1 x 9dB Outdoor Antenna 1 x 5dB Indoor Antenna 1 x 5m RG6-50 OHM Indoor Coaxial Cable 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 4.95kgs / 10.92lb One Package Size 43cm * 22cm * 24cm / 16.93inch * 8.66inch * 9.45inch Qty per Carton 4 Carton Weight 13.40kgs / 29.54lb Carton Size 46cm * 46cm * 50cm / 18.11inch * 18.11inch * 19.69inch Loading Container 20GP: 252 cartons * 4 pcs = 1008 pcs40HQ: 585 cartons * 4 pcs = 2340 pcs
£52.99
-
Mobile LED WCDMA 2100MHz & GSM 900MHz Signal Booster / Signal Repeater with Sucker Antenna, WCDMA&GSM
About Signal BoosterCell phone becomes especially helpful when people get into critical situations. In case of emergency a timely call can save a life. Unfortunately, there are still some places where one can find themselves - out of coverage. Usually those places are either too far from the cell phone base station or located inside underground constructions, for example: parking lots, tunnels, big stores, office buildings, cars, boats, house in remote areas, etc. Here we will bring you a new kind of LED signal booster. Welcome to buy!Features1. High-gain linear power amplifier. 2. ALC and AGC function technology. 3. Ultra-low noise receive amplifier. 4. There is no interference to the base station, right after the opening of the original system and the base station without the need to adjust parameters. 5. Stable and reliable electromagnetic compatibility design. 6. The base station dose not cause an increase in background noise, but will not lead to a decline in the quality of the base station communications. 7. With full-duplex communication mode. 8. It explores an effective and reasonable method to dispel the heat.Installation Steps1. Use your mobile phone to test signal strength outside house or on roof, -70dBm is the basic requirement (full bar). 2. Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal. 3. Run outdoor coaxial cable into building in a convenient location to connect with signal repeater. 4. Mount your indoor antenna with signal repeater. 5. Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Notices1. Connect outdoor (BTS) port with outdoor antenna. Connect indoor ANT (MS) port with indoor antenna. Outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away at least from each other. 2. Indoor and outdoor antennas must be separated by wall. 3. If the signal is still weak after installation, please check whether or not the outdoor antenna is pointed to signal tower correctly or elsewhere with stronger signal and confirm that the signal strength achieved -70dBm. 4. If no signal for a long time after installation, please check the device power adapter whether or not connected perfectly and connectors connect well. 5. If strength is not steady, please check if outdoor and indoor antennas are too close. Please ensure outdoor antenna has distance of 10 meters at least, with a barrier and not in a same horizontal line. 6. Packed the outdoor connector by waterproof glue, otherwise wet condition will reduce the signal cover area.Specification: General Frequency Range WCDMA 2100MHz, Uplink 1920-1980MHz, Downlink 2110-2170MHz, GSM 900MHz, Uplink 890-915MHz, Downlink 935-960MHz Gain 65dB Output Power Uplink 18-22dBm, Downlink 18-22dBm Automatic Gain Control >20dB Ripple in Band < 5dB Spurious Emission 9KHz~1GHz (<-36dBm), 1GHz~12.75GHz (<-30dBm) VSWR <2 MTBF >50000h Power Supply AC:90~265V, 50/60Hz; DC:12V 2A Power Consumption <20W Impedance 50ohm RF Connector N-Female N Work Environment Installs Way Wall Installation Environment Conditions IP40 Working Temperature -10C ~ 55C Working Humidity < 90% Dimensions & Weight Size 198 x 182 x 20mm Weight 1200g Package Include Package Contents 1 x 9dB Outdoor Antenna 1 x 5dB Indoor Antenna 1 x 5m RG6-50 OHM Indoor Coaxial Cable 1 x 10m RG6-50 OHM Outdoor Coaxial Cable 1 x Mounting Accessories Set 1 x AC Power Supply 1 x Manual Package Weight One Package Weight 3.78kgs / 8.34lb One Package Size 39cm * 22cm * 20cm / 15.35inch * 8.66inch * 7.87inch Qty per Carton 4 Carton Weight 15.90kgs / 35.05lb Carton Size 51cm * 45cm * 45cm / 20.08inch * 17.72inch * 17.72inch Loading Container 20GP: 258 cartons * 4 pcs = 1032 pcs40HQ: 599 cartons * 4 pcs = 2396 pcs
£48.99
-
Mobile Phone Anti-theft Alarm Display Stand with Remote Control for iPhone & iPod with 8-Pin Port, 8 Pin Cable
1. Security system is used to secure consumer electronic gadgets in exhibition or store open display against theft. This innovative system is easy to operate and is able to blend easily in any exhibits layout. 2. Charging function: The stand alone security device built in lithium battery, if the power outages that is also with security function. One set of external 5V power adapter, and it can be supply products for charging. 3. Alarming function: - Contactor alarm: When we pull up the contactor and back of parts VBH adhesive, then it will immediately issued warming sound. - Cutting cable alarm: When the alarm cable was pulled apart or cut off, then it will immediately issued warming sound. 4. Remote control function: The infrared remote control, anti-interference ability, sensitivity strong. 5. Material: ABS 6. Alarm volume: 95-120dB 7. Input voltage: 110-240V 8. Charging voltage: DC 5V 1A 9. Unlock: Infrared remote control 10. Installation: Stick adhesive.Specification: General Weight 16g Package Weight One Package Weight 0.21kgs / 0.45lb One Package Size 15cm * 9cm * 6cm / 5.91inch * 3.54inch * 2.36inch Qty per Carton 50 Carton Weight 8.50kgs / 18.74lb Carton Size 47cm * 32cm * 32cm / 18.5inch * 12.6inch * 12.6inch Loading Container 20GP: 554 cartons * 50 pcs = 27700 pcs40HQ: 1286 cartons * 50 pcs = 64300 pcs
£13.99
-
Mobile Phone Anti-theft Alarm Display Stand with Remote Control for Mobile Phones with Type-C / USB-C Port, Alarm Stand
1. Security system is used to secure consumer electronic gadgets in exhibition or store open display against theft. This innovative system is easy to operate and is able to blend easily in any exhibits layout. 2. Charging function: The stand alone security device built in lithium battery, if the power outages that is also with security function. One set of external 5V power adapter, and it can be supply products for charging. 3. Alarming function: - Contactor alarm: When we pull up the contactor and back of parts VBH adhesive, then it will immediately issued warming sound. - Cutting cable alarm: When the alarm cable was pulled apart or cut off, then it will immediately issued warming sound. 4. Remote control function: The infrared remote control, anti-interference ability, sensitivity strong. 5. Material: ABS 6. Alarm volume: 95-120dB 7. Input voltage: 110-240V 8. Charging voltage: DC 5V 1A 9. Unlock: Infrared remote control 10. Installation: Stick adhesive.Specification: General Material ABS Power Supply AC 110-240V Output Voltage 5V Standby Time 90 days Size 6*5*5cm Weight 107g Package Include Package Contents 1 x Charging Cable 1 x Display Stand 1 x 3M Adhesive & Clip Package Weight One Package Weight 0.19kgs / 0.42lb One Package Size 15cm * 9cm * 6cm / 5.91inch * 3.54inch * 2.36inch Qty per Carton 50 Carton Weight 8.00kgs / 17.64lb Carton Size 47cm * 32cm * 32cm / 18.5inch * 12.6inch * 12.6inch Loading Container 20GP: 554 cartons * 50 pcs = 27700 pcs40HQ: 1286 cartons * 50 pcs = 64300 pcs
£13.99
-
MOMAX Dispositivo antipérdida con posicionamiento de carga inalámbrica de tarjeta PINCARD BR8 de MOMAX, PINCARD BR8
1. Posicionamiento preciso global, dispositivo de llamada con un solo toque, carga inalámbrica. 2. Resistente al agua IP68, guía de luz intermitente, no es necesario descargar la aplicación. 3. Compatible con la red Find My de Apple. Siempre que haya dispositivos iOS en todo el mundo, se podrá rastrear la ubicación. 4. Diseño de orificio abierto, se puede colocar directamente en el llavero, identificar la ubicación con un clic y puede reproducir sonido al mismo tiempo, lo que hace que sea más fácil de encontrar. 5. Cuando salgas y guardes tu bolso en tu bolso, tu teléfono móvil te recordará automáticamente si estás a 100 metros del lugar para evitar dejar objetos atrás. 6. Batería de litio incorporada, compatible con carga inalámbrica, se puede utilizar durante 1 año después de una carga y se puede reciclar más de 300 veces. 7. Tres niveles de guía hacen que encontrar objetos sea más conveniente: la aplicación bloquea con precisión la ubicación donde apareció el artículo por última vez, lo que permite rastrearlos: El mapa de orientación de ruta muestra la ubicación y planifica la ruta para encontrar el objeto Guía de sonido: reproduce un sonido y un pitido como recordatorio Guía luminosa: La luz roja parpadea al emitir un sonido, lo que facilita su localización en entornos oscuros. 8. Parámetros: Capacidad de la batería: 100 mAh Sistemas operativos compatibles: iOS 14.5 / iPadOS 14.5 y superiores / macOS 12.5 y superiores Material: PVC Dimensiones: 54 mm x 45 mm x 3 mm Peso: 11g Especificación: Peso del paquete Peso de un paquete 0,06 kg/0,14 lb Un tamaño de paquete 12,5 cm x 8,5 cm x 2 cm (4,92 pulgadas x 3,35 pulgadas x 0,79 pulgadas) Cantidad por caja 90 Peso de la caja 6,13 kg/13,51 lb Tamaño de la caja 45 cm x 29 cm x 26 cm (17,72 pulgadas x 11,42 pulgadas x 10,24 pulgadas) Contenedor de carga 20GP: 785 cajas * 90 uds. = 70650 uds. 40HQ: 1824 cajas * 90 piezas = 164160 piezas
£21.99
-
Motion Detection Smart Alarm Wireless Connected Mini Battery Camera, W03
1. Operating system: Linux2. Online users: 4 users can watch online simultaneously3. App: O-KAM Pro - Overseas4. Processor: ingenic T235. Memory: 512Mb6. Illumination: 0.3～0.5Lux (Color Mode), 0Lux (Black and White Mode)7. Lens: GC20838. Viewing angle: D130 degrees diagonally9. Night vision: black and white night vision, automatic light-sensing switching10. Compression standard: H.264+ / MJPEF / JPEG11. Main stream: 1080P/15fps12. Sub-stream: 360P/15fps13. Bitrate: CBR/VBR two bitrate control modes, with an output bitrate range of 128～4096kbps14. Input: built-in -38dB microphone15. Sampling frequency/bit width: 8KHz/16bit16. Compression standard/bitrate: G711A17. Network protocol: TCP/IP/HTTP/TCP/UDP/DHCP/DNS/NTP/RTSP/P2P/IPv4, etc.18. Wireless network: IEEE802.11b/g/n19. Wireless frequency: 2.4~2.4835GHz WIFI6+BLE20. Wireless security encryption: 64/128-bit WEP/WPA-PSK/WPA2-PSK data encryption21. Wireless connection: QR code pairing, Bluetooth pairing22. Toggle button 1: Power On/Off23. Toggle button 2: /24. Reset button: long press to restore factory settings25. External TF card: supports T-Flash cards (up to 128GB)26. Cloud storage: supported27. Alarm detection: supports motion detection28. Charging voltage: DC5V±5% 1A29. Battery: 800mAh, continuous operation for approximately 4.5 hours, recommended charging time 4-5 hours30. Power consumption: 0.9W31. Package contents: main unit x 1, stand x 1, type-C cable x 1, instruction manual x 1, screw pack x 1Specification: Package Weight One Package Weight 0.12kgs / 0.26lb One Package Size 7cm * 8cm * 11cm / 2.76inch * 3.15inch * 4.33inch Qty per Carton 100 Carton Weight 13.10kgs / 28.88lb Carton Size 47cm * 32cm * 40cm / 18.5inch * 12.6inch * 15.75inch Loading Container 20GP: 443 cartons * 100 pcs = 44300 pcs40HQ: 1029 cartons * 100 pcs = 102900 pcs
£14.99
-
MS-190 Mini Motor Alarm Wind Screw Buzzer
1. Name: Alarm2. Material: Metal3. Power: 40W4. Decibel: 110dB5. Rated voltage: 220V AC6. Rated current: 3A7. Insulation resistance: 100MΩ (AT500 VDC)8. Size: 105x85mm9. Optional working methods: constant light, flashing, strobeSpecification: Package Weight One Package Weight 0.25kgs / 0.56lb One Package Size 15cm * 12cm * 12cm / 5.91inch * 4.72inch * 4.72inch Qty per Carton 118 Carton Weight 30.00kgs / 66.14lb Carton Size 50cm * 50cm * 60cm / 19.69inch * 19.69inch * 23.62inch Loading Container 20GP: 177 cartons * 118 pcs = 20886 pcs40HQ: 412 cartons * 118 pcs = 48616 pcs
£3.99
Has visto 384 de 642 productos